foratvise
Get Started
Equipment failure (breakdowns)

Seaming Mandrel/Roller Wear and Misalignment

Equipment failure (breakdowns)AvailabilityCapping and seaming

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 58 % of the line's lost time. Reported by 2 of the 82 studies that could observe it (limited evidence).

What happens

Continuous mechanical stress and friction during the seaming cycle gradually wear the mandrels and roller bearings (rulinas) of the seaming head, causing progressive misalignment between chuck, mandrel and rollers. This degradation alters the seam closure geometry and clearances until the sealing hardware either jams or breaks, or produces seams that no longer meet closure specification. The problem is aggravated when no preventive maintenance plan exists to replace worn parts before they reach a critical state.

What is done about it

Establish a preventive or condition-based maintenance plan that periodically inspects, measures wear tolerances, and replaces mandrels, rollers and bearings before they cause misalignment, complemented by seam-geometry verification after every component change or at defined running-hour intervals.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
1.0% [0.2–2.6%]
Expected share of lost time
0.6% [0.1–1.5%]
Share of lost time when present
58% [47–69%]
Studies / units
82 / 109
Evidence grade
C

Grade C: 2 to 4 studies, or an interval wider than 0.35.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    1.6% [0.2–5.2%]11 studies
  • Soft drinks, bottled water and juices
    0.9% [0.1–2.9%]26 studies
  • Brewing, wine and spirits
    1.1% [0.1–3.8%]11 studies
  • Bakery and pasta
    1.2% [0.1–4.7%]0 studies
  • Meat, poultry and seafood
    1.6% [0.2–5.5%]7 studies
  • Fruit and vegetable processing
    1.1% [0.2–4.0%]4 studies
  • Grain and oilseed milling
    1.2% [0.1–4.2%]3 studies
  • Sugar and confectionery
    1.2% [0.1–4.4%]3 studies
  • Snacks, coffee, tea and other foods
    1.1% [0.1–4.0%]4 studies
  • Animal feed and pet food
    1.1% [0.1–4.1%]4 studies
  • Food manufacturing (unspecified or mixed)
    1.1% [0.1–4.0%]9 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Continuous mechanical stress and friction during the seaming cycle gradually wear the mandrels and roller bearings (rulinas) of the seaming head, causing progressive misalignment between chuck, mandrel and rollers. This degradation alters the seam closure geometry and clearances until the sealing hardware either jams or breaks, or produces seams that no longer meet closure specification. The problem is aggravated when no preventive maintenance plan exists to replace worn parts before they reach a critical state.

How it looks in SCADA data

Engineering guidance

SCADA/MES logs unplanned stop events on the capper/seamer tagged as mechanical faults, with stop duration and frequency rising as running hours since the last overhaul accumulate. Downstream inspection or checkweighing stations show a parallel increase in seal/seam defect rejects that correlates with the same machine and time window, while maintenance work-order history shows reactive rather than scheduled interventions on mandrels and rollers.

Countermeasure

Engineering guidance

Establish a preventive or condition-based maintenance plan that periodically inspects, measures wear tolerances, and replaces mandrels, rollers and bearings before they cause misalignment, complemented by seam-geometry verification after every component change or at defined running-hour intervals.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 13.2 Ton · as reported: “Mal Sellado”
    Show verbatim quote
    mostrando un beneficio al pasar de 14.9 a 13.2 Toneladas de reproceso relacionadas a este problema, un beneficio del 11.3%
  2. Lost time: 14.9 Ton · as reported: “Mal Sellado”
    Show verbatim quote
    mostrando un beneficio al pasar de 14.9 a 13.2 Toneladas de reproceso relacionadas a este problema, un beneficio del 11.3%
  3. Share of loss events: 42.0 % · as reported: “averías mecánicas relacionadas con mandriles y desalineaciones”
    Show verbatim quote
    con un predominio de desgaste de rulinas (58 %) sobre averías mecánicas relacionadas con mandriles y desalineaciones (42 %)
  4. Share of loss events: 58.0 % · as reported: “desgaste de rulinas”
    Show verbatim quote
    con un predominio de desgaste de rulinas (58 %) sobre averías mecánicas relacionadas con mandriles y desalineaciones (42 %)
  5. Share of loss events: 72.0 % · as reported: “fallas en equipos sin plan preventivo”
    Show verbatim quote
    Se registraron 18 fallas críticas: el 72 % ocurrió en equipos sin plan preventivo