foratvise
Get Started
Filling and packaging line

Capping and seaming

Double seaming of three-piece food cans on a rotary seamer

Validated modelOEE bound 0.999 [0.864–1.000]20,000 Monte Carlo samples · seed 20261115 · computed November 16, 2026

In short

Capping and seaming can use at most 100 of every 100 planned hours. The rest goes to limits no plant can avoid.

  1. 100usable at most

The three limits that set it

Running time: up to 100 %

The rest are stops imposed by physics or by regulation: cleaning, changeovers, defrosting.

Speed: up to 100 %

How close to its maximum speed it can run without damaging the product or the equipment.

Good product: up to 100 %

Some product falls outside specification even with the process well under control.

See the technical detail

Technical detail

Uncertainty intervals, physical models per station and sources, for anyone who wants to check each figure.

1Scenario

Canned vegetables are closed in round three-piece steel cans of the 300-303 diameter group (a No. 303 can, 3 3/16 in). After filling, a can end is placed on each can and a rotary seamer with several seaming heads rolls the end curl and the body flange into a double seam in two operations (first-operation roll, second-operation roll) while the can is held by its chuck. The seamer is synchronised with the filler. The double seam is the hermetic closure of a low-acid food that is sterilised afterwards, so its integrity is regulated (21 CFR 113.60). Of the two closures of the processes that use this unit operation (screw caps on PET bottles of carbonated soft drinks, double seams on cans), the double seam is the one whose acceptance criteria and inspection duties are stated in openly readable regulations and guidance, so it is the scenario modelled here.

Provenance of inputsDeclared assumption22Verified quote10

2Results

Point value from the nominal parameters and 95% interval from 20,000 Monte Carlo draws of the uncertain parameters.
  • Body hook length aimed at (centre of the set-up aim)0.0825 inch
  • Cover (end) hook length aimed at (operating minimum plus the capability margin)0.0753 [0.0735–0.0792] inch
  • Internal seam length C = W - k (2 T_e + t_b) at the nominal seam length0.0881 [0.0822–0.0939] inch
  • Overlap at the nominal hook and seam lengths, BH + CH + T_e - W0.0513 [0.0461–0.0584] inch
  • Percent overlap at the nominal setting (overlap over internal seam length)58.2 [49.6–70.3] %
  • Body hook butting at the nominal setting84.3 [79.2–90.2] %
  • Standard deviation of the overlap (hook and seam-length dispersion)0.00312 [0.00276–0.00407] inch
  • Share of seams below the hold-for-investigation minimum overlap9.39 × 10⁻⁸ [1.49 × 10⁻¹²–5.09 × 10⁻⁴]
  • Share of seams below 45 % overlap4.37 × 10⁻⁴ [1.03 × 10⁻⁸–1.35 × 10⁻¹]
  • Share of seams below 70 % body hook butting2.65 × 10⁻⁷ [8.65 × 10⁻¹²–7.09 × 10⁻⁴]
  • TheoreticalMaximum OEE quality factor: share of seams meeting all three criteria with a capable seaming station1.000 [0.865–1.000]
  • TypicalQuality factor when the seam dimensions only just fill the operating limits (declared typical dispersion)0.986 [0.776–1.000]
  • Seaming time per can (roll revolutions over spindle speed; declared kinematics)0.300 [0.169–0.489] s
  • Cans per minute of the rotary seamer at the declared kinematics600 [348–1,111] 1/min
  • Plastic folding work per can end (rigid-perfectly-plastic lower bound)9.06 [5.97–16.94] J
  • TheoreticalMinimum mechanical work of double seaming per kg of packed product (plastic folding)0.0201 [0.0133–0.0377] kJ/kg
  • Share of cans destroyed by the teardown examinations4.17 × 10⁻⁵ [2.92 × 10⁻⁵–1.19 × 10⁻⁴]
  • TheoreticalMaximum yield of conforming cans (teardown samples destroyed)0.999958 [0.999881–0.999971]
  • TheoreticalMaximum availability (seaming-roll and chuck replacement forced by wear)0.9995 [0.9976–0.9998]
  • Availability with declared can-size changeovers0.972 [0.918–0.991]
  • TheoreticalPerformance factor: the seamer runs synchronised with the filler at its rated speed1.00
  • TheoreticalPhysics-bounded OEE0.999 [0.864–1.000]
  • OEE with declared can-size changeovers0.971 [0.839–0.990]

3Ceilings per dimension

Each dimension shows the ceilings the model computes and, where units are comparable, documented benchmarks. Colour and marker shape identify the ceiling type throughout the Oracle.
  • Theoretical
  • Best available technique
  • Best documented
  • Typical
Qualityhigher is better
  • TheoreticalMaximum OEE quality factor: share of seams meeting all three criteria with a capable seaming station1.000 [0.865–1.000]
  • TypicalQuality factor when the seam dimensions only just fill the operating limits (declared typical dispersion)0.986 [0.776–1.000]
Energy per unit of productkJ/kg · lower is better
  • TheoreticalMinimum mechanical work of double seaming per kg of packed product (plastic folding)0.0201 [0.0133–0.0377] kJ/kg
Yieldhigher is better
  • TheoreticalMaximum yield of conforming cans (teardown samples destroyed)0.999958 [0.999881–0.999971]
Availabilityhigher is better
  • TheoreticalMaximum availability (seaming-roll and chuck replacement forced by wear)0.9995 [0.9976–0.9998]
Performancehigher is better
  • TheoreticalPerformance factor: the seamer runs synchronised with the filler at its rated speed1.00
OEEhigher is better
  • TheoreticalPhysics-bounded OEE0.999 [0.864–1.000]

4Loss cascade

What separates each ceiling from the next one, from the physical limit to typical operation.
  1. TheoreticalTypicalQuality
    1.000 [0.865–1.000] → 0.986 [0.776–1.000] (gap 0.0132)

    The quality ceiling is the share of seams that meet three geometric criteria at once: an overlap of at least the hold-for-investigation minimum, an overlap of at least 45 % of the internal seam length and a body hook butting of at least 70 %. The overlap is the sum of the two hooks and the end plate minus the seam length, so its spread is the combined spread of the body hook, the cover hook and the seam length. A capable seaming station keeps its aim 3 to 4 standard deviations inside the operating limits of the hooks; when the dispersion grows until the hooks only just fill the operating limits, the low tail of the overlap crosses the 45 % line far more often. The causes of a wider dispersion are worn rolls and chucks (the seam lengthens), a base-plate pressure that drifts (the body hook changes length), flange width and end-curl variation of the incoming components, and roll settings that are not reset after a jam; this is why the regulation asks for visual checks every 30 minutes and teardowns every 4 hours.

5Physics-bounded OEE

The highest OEE the operation can reach: availability, performance and quality limited only by unavoidable stops and physical capability.
Fraction of loading time that remains after each unavoidable loss. Axis starts at 0.80.
  • Loading time (ideal)
    1.000
  • Availability
    factor 0.9995 [0.9976–0.9998]
    1.000 (−0.000)
  • Performance
    factor 1.00
    1.000 (−0.000)
  • Quality
    factor 1.000 [0.865–1.000]
    0.999 (−0.000)
  • Physics-bounded OEE
    0.999 [0.864–1.000]

6Full derivation

Mass and energy balances, rate-limiting step, process capability and unavoidable stops, with every term explained.

Scope. Canned vegetables are closed in round three-piece steel cans of the 300-303 diameter group (a No. 303 can, 3 3/16 in = 81 mm). A rotary seamer with NhN_h seaming heads places an end on each filled can and rolls the end curl and the body flange into a double seam in two operations while the can is held by its chuck; the seamer is synchronised with the filler. Of the two closures in the processes that use this unit operation (screw caps on PET bottles, double seams on cans), the double seam is the one whose acceptance criteria and inspection duties are stated in openly readable regulations and guidance (21 CFR 113.60, the CFIA metal-can manual, FAO guidance), so it is the scenario modelled. Symbols and their values, units, uncertainty distributions and sources are listed in the parameter table generated from config/physics/capping.yaml. Numbers quoted here are point values; the output table gives the Monte Carlo intervals.

1. Mass balance — maximum yield

Seaming adds an end to a can; it consumes no product. Product is lost only where conforming cans are destroyed: 21 CFR 113.60(a)(1) requires teardown examinations of the double seam "on enough containers from each seaming station", recorded at intervals that should not exceed 4 hours. A teardown destroys the can. With ntdn_{td} cans per station (at least one) every Δtd\Delta_{td} = 4 h at the machine rate n˙\dot n,

ftd=Nh ntdn˙ Δtd,Ymax=1−ftd=0.99996.f_{td} = \frac{N_h\,n_{td}}{\dot n\,\Delta_{td}}, \qquad Y_{max} = 1 - f_{td} = 0.99996 .

The visual seam checks every 30 minutes (one can per head) are made on cans that return to the line and cost nothing. Torn-down cans are conforming product, so this loss is a yield loss and does not enter the quality factor.

2. Energy balance — minimum work per can

The seam is formed by bending: the end curl is folded under the flange and both are pressed flat in the second operation. For a rigid-perfectly-plastic sheet of thickness tt and yield strength σy\sigma_y, the plastic moment per unit length of a fold line is

Mp=σy t24,M_p = \frac{\sigma_y\,t^2}{4},

and the plastic work of folding a length PP through an angle θ\theta is Mp θ PM_p\,\theta\,P. The end plate (TeT_e) is folded through a total angle θe\theta_e (about 2π2\pi: it is curled about half a turn and flattened back) and the body flange (tbt_b) through θb\theta_b (about π\pi), along the seam perimeter P=πDP = \pi D:

Wfold=(σyTe24 θe+σytb24 θb)πD=9.1 J per can,W_{fold} = \left(\frac{\sigma_y T_e^2}{4}\,\theta_e + \frac{\sigma_y t_b^2}{4}\,\theta_b\right)\pi D = 9.1\ \text{J per can},

or 0.020 kJ per kg of product for 0.45 kg per can. This is a lower bound of the mechanical work of a rate-independent plastic metal: friction of the rolls, strain hardening, elastic springback and the flow of the sealing compound come on top. No open source quotes a tinplate yield strength or the fold angles, so they are declared scenario values with ranges; the result scales linearly with σy\sigma_y and with the square of the plate thicknesses. It is negligible against the energy of the drives of a seamer and of the thermal processing that follows.

3. Rate-limiting step — seaming time and machine rate

Each head forms one seam while it travels the share ϕ\phi of a turret revolution (the rest is can infeed and discharge). The two seaming operations need together nrn_r revolutions of the rolls relative to the can at the spindle speed NsN_s, so

tseam=nrNs=0.30 s,n˙=Nh ϕtseam=600 cans/min.t_{seam} = \frac{n_r}{N_s} = 0.30\ \text{s}, \qquad \dot n = \frac{N_h\,\phi}{t_{seam}} = 600\ \text{cans/min}.

No open source states seaming kinematics, so nrn_r, NsN_s, ϕ\phi and NhN_h are declared; the time and rate are reported without a theoretical label (assumption a4). In the line, the seamer runs synchronised with the filler at its rated speed, and its performance factor is 1: no capability margin of the seam lengthens the cycle in this model.

4. Process capability — quality ceiling

Seam geometry. The double seam interlocks the body hook BHBH (formed from the body flange) and the cover hook CHCH (formed from the end curl) inside the seam length WW. Conservation of the folded lengths gives the overlap stated in 21 CFR 113.60 and in the FDA Bacteriological Analytical Manual:

OL=CH+BH+Te−W.OL = CH + BH + T_e - W .

The internal seam length, the space available for the hooks, is the seam length minus the three end-plate and two body-plate layers; the teardown formula of body hook butting in the CFIA manual applies a factor kk = 1.1 to the plate thicknesses:

C=W−k (2Te+tb).C = W - k\,(2T_e + t_b) .

Acceptance criteria. A seam is accepted when three geometric criteria hold at once:

  1. OL≥OLHFIOL \ge OL_{HFI} — the overlap is not below the hold-for-investigation minimum of the CFIA example guidelines for three-piece round sanitary cans (300-303 diameters, steel ends: 0.035 in; its operating limit is 0.040 in);
  2. OL/C≥pOLOL / C \ge p_{OL} = 45 % — good manufacturing practice cited by FAO: the overlap should be at least 45 % of the internal seam length;
  3. (BH−k tb)/C≥pBHB(BH - k\,t_b)/C \ge p_{BHB} = 70 % — the CFIA manual: "a minimum of 70% body hook butting is required to ensure an adequate seal".

Dimensions of a capable seaming station. The body hook is centred in its set-up aim (0.080–0.085 in for diameters 207.5–401, CFIA) and its dispersion is set by the operating limit ±ΔBH\pm\Delta_{BH} = ±0.008 in: a capable station keeps the aim zcapz_{cap} standard deviations inside it, σBH=ΔBH/zcap\sigma_{BH} = \Delta_{BH}/z_{cap}. The cover hook is aimed zcapz_{cap} standard deviations above its operating minimum, CH‾=CHmin+zcapσCH\overline{CH} = CH_{min} + z_{cap}\sigma_{CH} with CHminCH_{min} = 0.070 in. The seam length (set by the second-operation roll profile) and the plate thicknesses are declared, because the open guidance leaves them to the can maker. With zcapz_{cap} = 3.5, W‾\overline W = 0.115 in, TeT_e = 0.0085 in and tbt_b = 0.0075 in:

C=0.0881 in,OL=0.0513 in (1.30 mm),OL/C=58.2 %,BHB=84.3 %,σOL=σBH2+σCH2+σW2=0.0031 in.C = 0.0881\ \text{in}, \quad OL = 0.0513\ \text{in}\ (1.30\ \text{mm}), \quad OL/C = 58.2\,\%, \quad BHB = 84.3\,\%, \quad \sigma_{OL} = \sqrt{\sigma_{BH}^2+\sigma_{CH}^2+\sigma_W^2} = 0.0031\ \text{in}.

Conforming share. BHBH, CHCH and WW are independent normal variables. Each criterion is linear in them, so each marginal failure is a normal probability:

f1=Φ ⁣(OLHFI−OL‾σOL),f2=Φ ⁣(−OL‾−pOLC‾σBH2+σCH2+(1+pOL)2σW2),f3=Φ ⁣(−BH‾−ktb−pBHBC‾σBH2+pBHB2σW2),f_1 = \Phi\!\left(\frac{OL_{HFI} - \overline{OL}}{\sigma_{OL}}\right), \quad f_2 = \Phi\!\left(-\frac{\overline{OL} - p_{OL}\overline C}{\sqrt{\sigma_{BH}^2+\sigma_{CH}^2+(1+p_{OL})^2\sigma_W^2}}\right), \quad f_3 = \Phi\!\left(-\frac{\overline{BH} - k t_b - p_{BHB}\overline C}{\sqrt{\sigma_{BH}^2+p_{BHB}^2\sigma_W^2}}\right),

with Φ\Phi the standard normal distribution function: f1=9×10−8f_1 = 9\times10^{-8}, f2=4.4×10−4f_2 = 4.4\times10^{-4}, f3=2.6×10−7f_3 = 2.6\times10^{-7}. The three criteria are correlated (they share BHBH and WW), so the share of cans meeting all of them is integrated exactly: for a fixed seam length the butting criterion sets a lower limit of BHBH, and for fixed (W,BH)(W, BH) the two overlap criteria set a lower limit of CHCH whose probability is analytic,

Qmax=∫ϕW(w)∫BH≥pBHBC(w)+ktbϕBH(b)  Φ ⁣(CH‾−max⁡ ⁣(OLHFI, pOLC(w))+b+Te−wσCH)db dw=0.99956,Q_{max} = \int \phi_W(w) \int_{BH \ge p_{BHB}C(w) + k t_b} \phi_{BH}(b)\; \Phi\!\left(\frac{\overline{CH} - \max\!\big(OL_{HFI},\,p_{OL}C(w)\big) + b + T_e - w}{\sigma_{CH}}\right) db\, dw = 0.99956,

evaluated with Gauss–Hermite quadrature in WW and Gauss–Legendre quadrature in BHBH (checked against two million direct samples in the tests). The 45 % criterion binds: the seam length enters the overlap with weight 1+pOL1 + p_{OL}, so the seam length and its dispersion dominate the quality ceiling. When the hook dispersion only just fills the operating limits (ztypz_{typ} = 2 instead of 3.5) the conforming share falls to 0.986 (quality_typical).

Tightness (wrinkle rating), pressure ridge, juncture rating, cutovers, droops, false seams and compound defects are not modelled, so QmaxQ_{max} is an upper bound of the seam quality.

5. Unavoidable stops — maximum availability

No cleaning-in-place applies to a seamer, so the cleaning model is not used. The groove profile of the seaming rolls wears with every seam, and the CFIA manual notes that seam length "is partly dependent on the roll groove profile and the degree of seaming roll wear": as the rolls wear, the seam lengthens and the overlap shrinks (section 4), so worn rolls and chucks must be replaced and the seams set up again. This is a stop forced by a physical mechanism that accumulates during production. With a roll change of duration trt_r every Δr\Delta_r hours of running,

Amax=1−trΔr=0.9995.A_{max} = 1 - \frac{t_r}{\Delta_r} = 0.9995 .

Interval and duration are declared scenario values (no open source states them). Can-size changeovers are a product-mix decision and enter only

Ascen=Amax−tcoΔco=0.972.A_{scen} = A_{max} - \frac{t_{co}}{\Delta_{co}} = 0.972 .

The regulation adds visual checks every 30 minutes and after every jam, adjustment or start-up, and teardowns every 4 hours; they are made on cans taken from the running line and do not stop the seamer.

6. Physics-bounded OEE

Scope of the bound. The theoretical label of OEEmaxOEE_{max} means physics-bounded under the declared scenario: the ceiling follows from the physics and the regulatory acceptance criteria of the operation for the declared can, seamer and schedule, and it is a bound only conditional on those declarations. It follows the common definition of all models: AmaxA_{max} counts only stops required by regulation or forced by a physical mechanism, at their minimum duration; PmaxP_{max} is the ratio of the physics-limited ideal cycle to the cycle of the capable process; QmaxQ_{max} is the share of conforming units, and mass losses of conforming product (here the torn-down cans) are reported only as yield.

OEEmax=Amax×Pmax×Qmax=0.9995×1×0.99956=0.9991.OEE_{max} = A_{max} \times P_{max} \times Q_{max} = 0.9995 \times 1 \times 0.99956 = 0.9991 .

With the declared can-size changeovers, oee_scenario = 0.971. The Monte Carlo interval of OEEmaxOEE_{max} is wide on the low side because the seam length and the plate thicknesses are declared over ranges in which the 45 % overlap criterion becomes binding; the sensitivity table shows it.

Consistency with the filling model. The filling model bounds fill volume and give-away; this model starts with a filled can and counts neither fill nor head-space. Container sterility and the thermal process belong to the sterilization model; this model stops at the geometric integrity of the closure.

7. Assumptions and validity

See the assumption and validity lists generated from the configuration file. The most influential inputs (sensitivity table) are the nominal seam length and its dispersion, the plate thicknesses and the capability margin for quality, and the roll-change interval for availability.

Use for other processes. The codebook assigns capping_seaming to two processes. For canned vegetables the model applies directly. For carbonated soft drinks the closure is a screw cap applied to a PET bottle, a different mechanism for which no openly readable regulation with measurable conformity criteria was found; the ceiling of this model is used there as an approximation of the same form (a closure that either conforms or is rejected, and tooling that must be changed as it wears). It is not a bound derived for screw capping.

References

  • U.S. Code of Federal Regulations, Title 21, Part 113, Thermally processed low-acid foods packaged in hermetically sealed containers, § 113.60 Containers (4-1-25 edition).
  • Canadian Food Inspection Agency. Metal can defects: identification and classification manual (Table 4.1.5, example of double seam guidelines; source quoted there: Can Manufacturers Institute, voluntary industry can standards).
  • U.S. Food and Drug Administration. Bacteriological Analytical Manual, Chapter 22A, Examination of metal containers for integrity (overlap and percent-overlap formulas).
  • FAO. Planning and engineering data 2. Fish canning, Fisheries Circular 784, chapter 4 (overlap at least 45 % of the internal seam length).

7Parameters and provenance

Every input with its value, unit, role, uncertainty distribution and provenance. Open a quote to read the passage of the source that states the value.
  • BHaim,loBH_{aim,lo}80 thou

    Lower end of the set-up aim of the body hook length, round sanitary cans of 207.5 to 401 diameter

    Technology · Fixed

    Verified quote
    Show verbatim quote
    Body hook length Table Note 1 | 207.5 - 401 | .080 - .085 | .080 ± .008Metal can defects: identification and classification manual (opens in a new tab). Canadian Food Inspection Agency, Government of Canada, 2020. CFIA, Preventive controls for food: metal can defects
  • BHaim,hiBH_{aim,hi}85 thou

    Upper end of the set-up aim of the body hook length

    Technology · Fixed

    Verified quote
    Show verbatim quote
    Body hook length Table Note 1 | 207.5 - 401 | .080 - .085 | .080 ± .008Metal can defects: identification and classification manual (opens in a new tab). Canadian Food Inspection Agency, Government of Canada, 2020. CFIA, Preventive controls for food: metal can defects
  • ΔBH\Delta_{BH}8 thou

    Half-width of the operating limit of the body hook length (.080 ± .008 in)

    Technology · Fixed

    Verified quote
    Show verbatim quote
    Body hook length Table Note 1 | 207.5 - 401 | .080 - .085 | .080 ± .008Metal can defects: identification and classification manual (opens in a new tab). Canadian Food Inspection Agency, Government of Canada, 2020. CFIA, Preventive controls for food: metal can defects
  • CHminCH_{min}70 thou

    Operating minimum of the cover (end) hook length, diameters 300 to 401

    Technology · Fixed

    Verified quote
    Show verbatim quote
    End hook length Table Note 2 | 300 - 401 | | .070 Min.Metal can defects: identification and classification manual (opens in a new tab). Canadian Food Inspection Agency, Government of Canada, 2020. CFIA, Preventive controls for food: metal can defects
  • OLHFIOL_{HFI}35 thou

    Minimum optical overlap below which the cans are held for investigation (steel ends, diameters 300-303)

    Technology · Fixed

    Verified quote
    Show verbatim quote
    Optical overlap | 300-303 | | 0040 Min. | .035 Min. | {not developed}Metal can defects: identification and classification manual (opens in a new tab). Canadian Food Inspection Agency, Government of Canada, 2020. CFIA, Preventive controls for food: metal can defects
  • pOLp_{OL}45 %

    Minimum overlap as a share of the internal seam length (good manufacturing practice)

    Regulatory · Fixed

    Verified quote
    Show verbatim quote
    Good manufacturing practice indicates that the. overlap should be at least 45 % of the internal seam lenght to ensure that the seam will function correctly and resist to minor abuse.Planning and engineering data 2. Fish canning (FAO Fisheries Circular No. 784), chapter 4: Processing operations (opens in a new tab). Food and Agriculture Organization of the United Nations, 1988. FAO Fisheries Circular No. 784, FIIU/C784(En)
  • pBHBp_{BHB}70 %

    Minimum body hook butting (internal body hook length over internal seam length)

    Technology · Fixed

    Verified quote
    Show verbatim quote
    Experience indicates that a minimum of 70% body hook butting is required to ensure an adequate seal.Metal can defects: identification and classification manual (opens in a new tab). Canadian Food Inspection Agency, Government of Canada, 2020. CFIA, Preventive controls for food: metal can defects
  • kk1.1

    Factor applied to the plate thicknesses in the internal seam length (teardown formula of body hook butting)

    Technology · Fixed

    Verified quote
    Show verbatim quote
    % Body Hook Butting = (BH − 1.1tb ÷ SL − 1.1(2te + tb)) × 100Metal can defects: identification and classification manual (opens in a new tab). Canadian Food Inspection Agency, Government of Canada, 2020. CFIA, Preventive controls for food: metal can defects
  • zcapz_{cap}3.5

    Capability margin of a capable seaming station: number of standard deviations between the aim and the operating limits of the hooks

    Scenario · Uniform 3 to 4

    Declared assumption

    Operating choice, point value at the centre of the declared range 3-4 (capability index 1.0-1.33 against the operating limits). Sets sigma_BH = tolerance / z and the end-hook aim = operating minimum + z sigma_CH.

  • ztypz_{typ}2

    Typical capability margin: the hook dimensions only just fill the operating limits

    Scenario · Uniform 1.5 to 2.5

    Declared assumption

    Declared typical dispersion, used only for quality_typical.

  • σCH\sigma_{CH}1.5 thou

    Standard deviation of the cover hook length of a capable seaming station

    Scenario · Uniform 1 to 2.5 thou

    Declared assumption

    No open source with measured seam-dimension dispersions was found; declared assumption.

  • Wˉ\bar W115 thou

    Nominal seam length (width, height) set by the second-operation roll profile

    Scenario · Uniform 110 to 120 thou

    Declared assumption

    The open guidance read gives no seam-length guideline for this can size (the can maker supplies it); declared assumption. Overlap and the two percentages fall as the seam length grows.

  • σW\sigma_W1.5 thou

    Standard deviation of the seam length

    Scenario · Uniform 1 to 2.5 thou

    Declared assumption
  • TeT_e8.5 thou

    Thickness of the end (cover) plate

    Scenario · Uniform 7.5 to 9.5 thou

    Declared assumption

    Tinplate end of about 0.22 mm; declared assumption.

  • tbt_b7.5 thou

    Thickness of the body plate

    Scenario · Uniform 6.5 to 8.5 thou

    Declared assumption

    Tinplate body of about 0.19 mm; declared assumption.

  • NhN_h6

    Number of seaming heads of the rotary seamer

    Scenario · Fixed

    Declared assumption
  • ϕ\phi0.5

    Share of a turret revolution during which a head is seaming (the rest is can infeed and discharge)

    Scenario · Uniform 0.4 to 0.6

    Declared assumption
  • nrn_r10

    Revolutions of the seaming rolls around the can for both operations together

    Scenario · Uniform 6 to 14

    Declared assumption

    No open source with seaming kinematics was found; declared assumption.

  • NsN_s2,000 1/min

    Rotational speed of the seaming head (rolls relative to the can)

    Scenario · Uniform 1,500 to 2,500 1/min

    Declared assumption
  • Δtd\Delta_{td}4 h

    Longest interval between teardown examinations of each seaming station

    Regulatory · Fixed

    Verified quote
    Show verbatim quote
    Such examinations and recordings should be made at intervals not to ex- ceed 4 hours.21 CFR Part 113 — Thermally Processed Low-Acid Foods Packaged in Hermetically Sealed Containers (4-1-25 Edition) (opens in a new tab). U.S. Government Publishing Office (Code of Federal Regulations), 2025. p. 29. 21 CFR 113 (2025)
  • ntdn_{td}1

    Cans destroyed per seaming station at each teardown examination

    Scenario · Uniform 1 to 2

    Declared assumption

    21 CFR 113.60(a)(1) asks for 'enough containers from each seaming station' without a number; one can per station is the least.

  • Δr\Delta_{r}2,000 h

    Running time between two replacements of worn seaming rolls and chucks

    Scenario · Uniform 500 to 4,000 h

    Declared assumption

    Wear-limited interval; no open source states it. Declared assumption.

  • trt_{r}1 h

    Duration of a roll and chuck replacement with the set-up check of the seams

    Scenario · Uniform 0.5 to 2 h

    Declared assumption
  • Δco\Delta_{co}72 h

    Running time between two can-size changeovers

    Scenario · Uniform 24 to 168 h

    Declared assumption
  • tcot_{co}2 h

    Duration of a can-size changeover (chucks

    Scenario · Uniform 1 to 3 h

    Declared assumption
  • σy\sigma_y350 MPa

    Yield strength of the tinplate (end and body)

    Scenario · Uniform 250 to 550 MPa

    Declared assumption

    Range of tinplate tempers; no open source with a quotable value was used.

  • DD80.96 mm

    Diameter of the No. 303 can (3 3/16 in)

    Scenario · Fixed

    Declared assumption

    Can-size designation: first digit whole inches, next two digits sixteenths of an inch; 3 + 3/16 in = 80.96 mm.

  • θe\theta_e6.2832 radian

    Total plastic fold angle of the end curl while it becomes the cover hook (both operations)

    Scenario · Uniform 4.7124 to 7.854 radian

    Declared assumption

    About 2 pi (range 1.5 pi to 2.5 pi): the curl is bent through about half a turn and flattened back; declared assumption.

  • θb\theta_b3.1416 radian

    Total plastic fold angle of the body flange while it becomes the body hook

    Scenario · Uniform 2.3562 to 4.7124 radian

    Declared assumption

    About pi (range 0.75 pi to 1.5 pi); declared assumption.

  • mpm_p0.45 kg

    Mass of product per No. 303 can

    Scenario · Fixed

    Declared assumption

8Benchmarks

Documented values from open sources used to check the ceilings; no documented value may beat the theoretical limit.

None documented in this release.

9Unavoidable stops

Stops that physics or regulation impose; they set the maximum availability.
  • Replacement of worn seaming rolls and chucksVerified quote

    The groove profile of the seaming rolls wears with every seam; as it wears the seam lengthens and the overlap shrinks, so worn rolls must be replaced and the seams set up again. Interval and duration are declared scenario values.

    Show verbatim quote
    Seam length is partly dependent on the roll groove profile and the degree of seaming roll wear.Metal can defects: identification and classification manual (opens in a new tab). Canadian Food Inspection Agency, Government of Canada, 2020. CFIA, Preventive controls for food: metal can defects
  • Can-size changeover (scenario stop: availability_scenario only)Declared assumption

    A new can size requires other chucks, rolls and feed parts and a new seam set-up; a decision of the product mix, not physics.

10Assumptions

  1. Body hook, cover hook and seam length are independent and normally distributed from can to can at one seaming station; the body hook is centred in its set-up aim and the cover hook aimed z_cap standard deviations above its operating minimum, the same capability margin that sets the body-hook dispersion from its operating limits.
  2. The overlap is the calculated overlap of 21 CFR 113.60, CH + BH + T - W; the guidance warns that it can over- or underestimate the optical overlap, and no adjustment factor is added. The internal seam length uses the factor 1.1 on the plate thicknesses of the teardown formula of body hook butting.
  3. A can is nonconforming when any of the three geometric criteria fails. Tightness (wrinkle rating), pressure ridge, juncture rating, cutovers, droops, false seams and compound defects are not modelled, so the quality ceiling is an upper bound.
  4. The seamer runs synchronised with the filler at its rated speed (performance factor 1); the seaming kinematics are declared, so the rate and the seaming time are reported without a theoretical label.
  5. Availability: the only stop forced by a physical mechanism is the replacement of rolls and chucks worn by seaming; no cleaning-in-place applies to the seamer, so the cleaning model is not used. Can-size changeovers are a product-mix decision and enter only availability_scenario and oee_scenario. Visual seam checks (every 30 minutes) are made on cans taken from the running line.
  6. Teardown cans are conforming product destroyed by the examination: they reduce the yield, not the quality factor. The plastic folding work is a rigid-perfectly-plastic lower bound (no friction, strain hardening, elastic springback or compound flow).

11Range of validity

  • Round three-piece sanitary food cans with steel ends of the 300-303 diameter group; other sizes, aluminium ends, two-piece and non-round cans have other guidelines.
  • Screw capping of bottles is not covered: its acceptance criteria (application and removal torque) are not stated in open regulations.

12Sensitivity

Elasticity: relative change of the output for a relative change of each parameter. Spearman rank correlation from the Monte Carlo draws is shown alongside.
  • Wˉ\bar WNominal seam length (width, height) set by the second-operation roll profile
    elasticity -1.732Spearman ρ -0.81
  • CHminCH_{min}Operating minimum of the cover (end) hook length, diameters 300 to 401
    elasticity +0.100Spearman ρ —
  • BHaim,hiBH_{aim,hi}Upper end of the set-up aim of the body hook length
    elasticity +0.032Spearman ρ —
  • pOLp_{OL}Minimum overlap as a share of the internal seam length (good manufacturing practice)
    elasticity -0.030Spearman ρ —
  • BHaim,loBH_{aim,lo}Lower end of the set-up aim of the body hook length, round sanitary cans of 207.5 to 401 diameter
    elasticity +0.029Spearman ρ —
  • TeT_eThickness of the end (cover) plate
    elasticity +0.008Spearman ρ +0.19
  • kkFactor applied to the plate thicknesses in the internal seam length (teardown formula of body hook butting)
    elasticity +0.006Spearman ρ —
  • zcapz_{cap}Capability margin of a capable seaming station: number of standard deviations between the aim and the operating limits of the hooks
    elasticity +0.005Spearman ρ +0.14
  • ΔBH\Delta_{BH}Half-width of the operating limit of the body hook length (.080 ± .008 in)
    elasticity -0.002Spearman ρ —
  • σW\sigma_WStandard deviation of the seam length
    elasticity -0.002Spearman ρ -0.18
  • tbt_bThickness of the body plate
    elasticity +0.002Spearman ρ +0.05
  • σCH\sigma_{CH}Standard deviation of the cover hook length of a capable seaming station
    elasticity +0.001Spearman ρ +0.16
  • Δr\Delta_{r}Running time between two replacements of worn seaming rolls and chucks
    elasticity +0.001Spearman ρ +0.23
  • trt_{r}Duration of a roll and chuck replacement with the set-up check of the seams
    elasticity -0.001Spearman ρ -0.15
  • pBHBp_{BHB}Minimum body hook butting (internal body hook length over internal seam length)
    elasticity 0.000Spearman ρ —
  • Output rises with the parameter
  • Output falls with the parameter

13Validation checks

A model is published only when every check passes.
  • Dimensional analysis23 outputs converted to their declared unitsPassed
  • Every cited value verified against its source10 verified, 0 failedPassed
  • No documented value beats the theoretical limitPassed
  • Ceilings in physical orderPassed
  • Fractions within 0 and 1Passed

14Causes of loss in this operation

Probability that each cause is documented as a relevant loss of a line, pooled over all segments.

15References

  1. 21 CFR Part 113 — Thermally Processed Low-Acid Foods Packaged in Hermetically Sealed Containers (4-1-25 Edition) (opens in a new tab). U.S. Government Publishing Office (Code of Federal Regulations), 2025. p. 29. 21 CFR 113 (2025)
  2. Metal can defects: identification and classification manual (opens in a new tab). Canadian Food Inspection Agency, Government of Canada, 2020. CFIA, Preventive controls for food: metal can defects
  3. Planning and engineering data 2. Fish canning (FAO Fisheries Circular No. 784), chapter 4: Processing operations (opens in a new tab). Food and Agriculture Organization of the United Nations, 1988. FAO Fisheries Circular No. 784, FIIU/C784(En)
  4. fda_bam_ch22a_2001

Processes that use this operation