foratvise
Get Started
Equipment failure (breakdowns)

Sensor fouling or malfunction

Equipment failure (breakdowns)AvailabilityWhole line or unspecified equipment

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 1 of the 127 studies that could observe it (sparse evidence).

What happens

Product residue, condensation, dust or grease accumulates on the sensing face of level, position or presence sensors (such as tank float switches or photoelectric/proximity sensors), altering the signal they return or blocking the moving element. Over time the deposit either degrades detection accuracy or fully prevents a valid state change, causing the control system to receive a stuck or erroneous reading.

What is done about it

Implement scheduled cleaning or wipe-down of sensing surfaces as part of routine sanitation, and specify sensors rated for the process environment (self-cleaning, flush-mounted or non-contact designs) in areas prone to fouling. Add signal diagnostics or redundant sensing where feasible so drift or stuck readings trigger a maintenance alert before causing a stop.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.5% [0.1–1.5%]
Expected share of lost time
0.3% [0.1–0.9%]
Share of lost time when present
57% [47–67%]
Studies / units
127 / 161
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.1–2.2%]13 studies
  • Soft drinks, bottled water and juices
    0.6% [0.1–2.0%]26 studies
  • Brewing, wine and spirits
    0.6% [0.1–2.4%]11 studies
  • Bakery and pasta
    0.8% [0.1–2.8%]24 studies
  • Meat, poultry and seafood
    0.6% [0.1–2.3%]9 studies
  • Fruit and vegetable processing
    0.7% [0.1–2.5%]7 studies
  • Grain and oilseed milling
    0.7% [0.1–2.5%]6 studies
  • Sugar and confectionery
    0.6% [0.1–2.2%]9 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.1–2.4%]5 studies
  • Animal feed and pet food
    0.6% [0.1–2.6%]7 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.1–2.3%]10 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Product residue, condensation, dust or grease accumulates on the sensing face of level, position or presence sensors (such as tank float switches or photoelectric/proximity sensors), altering the signal they return or blocking the moving element. Over time the deposit either degrades detection accuracy or fully prevents a valid state change, causing the control system to receive a stuck or erroneous reading.

How it looks in SCADA data

Engineering guidance

SCADA/MES shows the affected sensor signal frozen at a fixed value or oscillating erratically while the physical process state clearly changes, often accompanied by a fault or out-of-range alarm on that tag. The associated machine or station enters a fault or hold state with repeated short stop events that correlate with maintenance log entries for sensor cleaning or replacement rather than mechanical repair.

Countermeasure

Engineering guidance

Implement scheduled cleaning or wipe-down of sensing surfaces as part of routine sanitation, and specify sensors rated for the process environment (self-cleaning, flush-mounted or non-contact designs) in areas prone to fouling. Add signal diagnostics or redundant sensing where feasible so drift or stuck readings trigger a maintenance alert before causing a stop.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Time between events: 27.6 not reported · as reported: “Filling Tank Float Sensor”
    Show verbatim quote
    Waktu Kerusakan Weibull MTTF 27,621
  2. Mean event duration: 219 not reported · as reported: “Filling Tank Float Sensor”
    Show verbatim quote
    Waktu Perbaikan Lognormal MTTF 219
  3. Lost time: 52.7 h · as reported: “Sensores sucios”
    Show verbatim quote
    el tiempo de paradas por sensores sucios corresponden al 23.15% del total de horas y es el principal motivo de paradas de la Línea 1 con 52.68 horas en el año de estudio, lo cual representa un 20.62% del total de horas de paradas por fallas de componentes en dicha línea.
  4. Share of lost time: 20.6 % · as reported: “Sensores sucios”
    Show verbatim quote
    el tiempo de paradas por sensores sucios corresponden al 23.15% del total de horas y es el principal motivo de paradas de la Línea 1 con 52.68 horas en el año de estudio, lo cual representa un 20.62% del total de horas de paradas por fallas de componentes en dicha línea.
  5. Share of lost time: 23.2 % · as reported: “Sensores sucios”
    Show verbatim quote
    el tiempo de paradas por sensores sucios corresponden al 23.15% del total de horas y es el principal motivo de paradas de la Línea 1 con 52.68 horas en el año de estudio