foratvise
Get Started
Process defects (scrap and rework)

Rework due to separation process deviation

Process defects (scrap and rework)QualitySeparation (centrifugation, filtration, membranes)

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 48 % of the line's lost time. Reported by 1 of the 37 studies that could observe it (sparse evidence).

What happens

During centrifugal or membrane separation, drift in flow rate, temperature, pressure or feed composition causes the separated streams (e.g. phases, solids content, clarity) to fall outside the target specification. The affected batch or portion of product cannot be released as first-pass good and must be routed back through the process for rework.

What is done about it

Tighten closed-loop control of feed flow, temperature and pressure to the separator, install or recalibrate inline quality sensors for early detection of drift, and apply statistical process control with tighter alarm bands so corrective action is taken before out-of-spec product is generated. Periodic maintenance and verification of separator discs, bowls or membranes also helps maintain stable separation performance.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
1.0% [0.2–3.0%]
Expected share of lost time
0.5% [0.1–1.4%]
Share of lost time when present
48% [36–60%]
Studies / units
37 / 44
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    1.1% [0.1–4.6%]5 studies
  • Soft drinks, bottled water and juices
    1.1% [0.1–4.8%]1 study
  • Brewing, wine and spirits
    1.2% [0.1–4.7%]1 study
  • Bakery and pasta
    1.2% [0.1–4.9%]0 studies
  • Meat, poultry and seafood
    1.1% [0.1–4.6%]2 studies
  • Fruit and vegetable processing
    1.1% [0.1–4.7%]3 studies
  • Grain and oilseed milling
    1.1% [0.1–4.3%]6 studies
  • Sugar and confectionery
    1.1% [0.1–4.2%]3 studies
  • Snacks, coffee, tea and other foods
    1.6% [0.2–6.3%]4 studies
  • Animal feed and pet food
    1.1% [0.1–4.3%]5 studies
  • Food manufacturing (unspecified or mixed)
    1.1% [0.1–4.3%]7 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

During centrifugal or membrane separation, drift in flow rate, temperature, pressure or feed composition causes the separated streams (e.g. phases, solids content, clarity) to fall outside the target specification. The affected batch or portion of product cannot be released as first-pass good and must be routed back through the process for rework.

How it looks in SCADA data

Engineering guidance

MES/SCADA records show quality parameters (density, turbidity, moisture, separation efficiency) drifting outside control limits while the machine remains in running state, followed by a diversion valve or recycle loop activation and a batch flagged as rework rather than good output. Rework volume counters increase without a corresponding rise in finished-good output.

Countermeasure

Engineering guidance

Tighten closed-loop control of feed flow, temperature and pressure to the separator, install or recalibrate inline quality sensors for early detection of drift, and apply statistical process control with tighter alarm bands so corrective action is taken before out-of-spec product is generated. Periodic maintenance and verification of separator discs, bowls or membranes also helps maintain stable separation performance.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of lost time: 23.3 % · as reported: “rework losses”
    Show verbatim quote
    the most influencing factors to decrease the effectiveness of DIBN machines are rework losses (23.33%), reduced yield losses (20.17%) and reduced speed of 19.49%.