foratvise
Get Started
Process defects (scrap and rework)

Label too short / undersized label

Process defects (scrap and rework)QualityLabeling and coding

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 45 % of the line's lost time. Reported by 0 of the 85 studies that could observe it (sparse evidence).

What happens

The label stock fed to the applicator is cut or dispensed shorter than the specified length, or the label web is mis-registered, so the finished container ends up with a label that does not fully cover the designated panel or wrap the required circumference. The defect is typically caused by incorrect cutting/dispensing settings, worn cutting blades, label stock variability, or sensor misregistration on the labeling unit.

What is done about it

Verify and recalibrate the label length/cut-off setting and web registration against the specified dimension, inspect and replace worn cutting or dispensing components, and qualify incoming label stock for consistent dimensions. Implement in-line label-coverage verification with automatic reject diversion to prevent short labels from reaching finished goods.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.4% [0.1–1.3%]
Expected share of lost time
0.2% [0.0–0.6%]
Share of lost time when present
45% [32–57%]
Studies / units
85 / 113
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.5% [0.0–2.0%]11 studies
  • Soft drinks, bottled water and juices
    0.4% [0.0–1.5%]29 studies
  • Brewing, wine and spirits
    0.5% [0.0–1.9%]13 studies
  • Bakery and pasta
    0.5% [0.0–2.1%]1 study
  • Meat, poultry and seafood
    0.5% [0.0–2.0%]4 studies
  • Fruit and vegetable processing
    0.5% [0.0–2.0%]4 studies
  • Grain and oilseed milling
    0.5% [0.0–1.9%]3 studies
  • Sugar and confectionery
    0.5% [0.0–2.1%]3 studies
  • Snacks, coffee, tea and other foods
    0.5% [0.0–1.9%]4 studies
  • Animal feed and pet food
    0.5% [0.0–2.0%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.5% [0.0–1.9%]9 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The label stock fed to the applicator is cut or dispensed shorter than the specified length, or the label web is mis-registered, so the finished container ends up with a label that does not fully cover the designated panel or wrap the required circumference. The defect is typically caused by incorrect cutting/dispensing settings, worn cutting blades, label stock variability, or sensor misregistration on the labeling unit.

How it looks in SCADA data

Engineering guidance

Vision inspection or label-presence sensors downstream flag rejects for incomplete label coverage, with a rising reject counter tied to the labeling station while the machine continues running in normal production state. MES/SCADA logs show no stoppage or fault alarm, only an increase in quality-reject tags attributed to the labeling unit, often correlated with a specific label-reel or batch changeover.

Countermeasure

Engineering guidance

Verify and recalibrate the label length/cut-off setting and web registration against the specified dimension, inspect and replace worn cutting or dispensing components, and qualify incoming label stock for consistent dimensions. Implement in-line label-coverage verification with automatic reject diversion to prevent short labels from reaching finished goods.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of lost time: 0.231 % · as reported: “Etiket kısalığı”
    Show verbatim quote
    Ekip yaptığı çalışmada bu probleme bağlı olarak yaşanan en fazla kaybın % 0,231 lik oran ile etiket kısalığına bağlı olduğunu tespit etmiştir.