foratvise
Get Started
Setup and adjustments

Tool/mould preparation during changeover

Setup and adjustmentsAvailabilityBaking

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 0 of the 60 studies that could observe it (sparse evidence).

What happens

Before a new product or format can be baked, the required tools, moulds, trays or cutting dies must be selected, cleaned, fitted and adjusted on the oven line, which consumes time between the last good unit of the previous run and the first good unit of the next. This preparation work is organisational rather than a mechanical failure, and its duration depends on how well tooling is staged, labelled and maintained beforehand.

What is done about it

Apply SMED principles by pre-staging, pre-heating and kitting tools and moulds offline before the changeover window starts, and standardise tool identification and storage so the correct set is retrieved without delay. Use quick-change tooling fixtures and maintain a tooling condition checklist to avoid last-minute cleaning or repair during the changeover itself.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.4% [0.1–1.4%]
Expected share of lost time
0.2% [0.0–0.8%]
Share of lost time when present
57% [44–67%]
Studies / units
60 / 73
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.5% [0.0–2.2%]5 studies
  • Soft drinks, bottled water and juices
    0.5% [0.0–2.2%]1 study
  • Brewing, wine and spirits
    0.5% [0.0–2.1%]0 studies
  • Bakery and pasta
    0.5% [0.0–1.8%]27 studies
  • Meat, poultry and seafood
    0.5% [0.0–2.1%]2 studies
  • Fruit and vegetable processing
    0.5% [0.0–2.1%]2 studies
  • Grain and oilseed milling
    0.5% [0.0–2.3%]0 studies
  • Sugar and confectionery
    0.5% [0.0–2.0%]8 studies
  • Snacks, coffee, tea and other foods
    0.5% [0.0–2.0%]4 studies
  • Animal feed and pet food
    0.5% [0.0–2.2%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.5% [0.0–2.2%]7 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Before a new product or format can be baked, the required tools, moulds, trays or cutting dies must be selected, cleaned, fitted and adjusted on the oven line, which consumes time between the last good unit of the previous run and the first good unit of the next. This preparation work is organisational rather than a mechanical failure, and its duration depends on how well tooling is staged, labelled and maintained beforehand.

How it looks in SCADA data

Engineering guidance

The line or oven state log shows an extended period in changeover/setup mode with no production counts registered, often preceded by an operator-entered changeover reason code; upstream and downstream equipment may show starvation or idle states while tooling is being readied. No equipment fault alarms accompany the stop, distinguishing it from unplanned failure events.

Countermeasure

Engineering guidance

Apply SMED principles by pre-staging, pre-heating and kitting tools and moulds offline before the changeover window starts, and standardise tool identification and storage so the correct set is retrieved without delay. Use quick-change tooling fixtures and maintain a tooling condition checklist to avoid last-minute cleaning or repair during the changeover itself.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 3.00 min:s · as reported: “Tool preparation”
    Show verbatim quote
    Alistamiento de herramientas 3:00