foratvise
Get Started
Equipment failure (breakdowns)

Tray Corner Ear Flare Defect

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 1 of the 112 studies that could observe it (sparse evidence).

What happens

Worn, misaligned or improperly set folding tooling (fold bars, mandrels or creasing blades) in the tray folding unit fails to fully compress and crease the corner ear of the tray blank, so the folded flap springs back open instead of lying flat against the side wall. The flared ear then catches on downstream guides or forming surfaces, causing tray jams and mechanical faults that require intervention to clear and realign the tooling.

What is done about it

Inspect and replace worn fold bars, mandrels or creasing blades, and verify the alignment and pressure setting of the folding station against the tooling specification. Implement a periodic preventive maintenance check on the ear-folding mechanism and confirm incoming blank quality (score lines, material stiffness) is within tolerance to ensure a clean, flat fold.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.6% [0.1–1.6%]
Expected share of lost time
0.3% [0.1–0.9%]
Share of lost time when present
57% [46–68%]
Studies / units
112 / 155
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.1–2.3%]14 studies
  • Soft drinks, bottled water and juices
    0.8% [0.1–2.5%]33 studies
  • Brewing, wine and spirits
    0.6% [0.1–2.2%]14 studies
  • Bakery and pasta
    0.7% [0.1–2.6%]6 studies
  • Meat, poultry and seafood
    0.7% [0.1–2.5%]6 studies
  • Fruit and vegetable processing
    0.7% [0.1–2.7%]4 studies
  • Grain and oilseed milling
    0.7% [0.1–2.4%]4 studies
  • Sugar and confectionery
    0.7% [0.1–2.6%]4 studies
  • Snacks, coffee, tea and other foods
    0.7% [0.1–2.4%]8 studies
  • Animal feed and pet food
    0.7% [0.1–2.4%]5 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.1–2.3%]14 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Worn, misaligned or improperly set folding tooling (fold bars, mandrels or creasing blades) in the tray folding unit fails to fully compress and crease the corner ear of the tray blank, so the folded flap springs back open instead of lying flat against the side wall. The flared ear then catches on downstream guides or forming surfaces, causing tray jams and mechanical faults that require intervention to clear and realign the tooling.

How it looks in SCADA data

Engineering guidance

SCADA/MES logs show recurrent fault or jam alarms localized to the tray folding or ear-forming station, with downtime events attributed to that station rather than a general line stop. Fault counters at the folding axis or servo increase, cycle time or station dwell time shows irregular spikes, and downstream units may register starvation while the jam is cleared.

Countermeasure

Engineering guidance

Inspect and replace worn fold bars, mandrels or creasing blades, and verify the alignment and pressure setting of the folding station against the tooling specification. Implement a periodic preventive maintenance check on the ear-folding mechanism and confirm incoming blank quality (score lines, material stiffness) is within tolerance to ensure a clean, flat fold.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Number of events: 30.0 events · as reported: “Tray ear flare”
    Show verbatim quote
    ความสูญเสียหลักเกิดจากปัญหาหูถาดอ้า ซึ่งมีความถี่ในการเกิดสูงสุดถึง 30 ครั้ง (เฉลี่ย 2.50 ครั้งต่อเดือน)