foratvise
Get Started
Equipment failure (breakdowns)

Tray-forming clamp/finger mechanism fault

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 2 of the 112 studies that could observe it (limited evidence).

What happens

The tray former uses a set of mechanical fingers or clamps to hold, fold and release the tray blank while it is shaped; wear, misalignment or jamming of these clamping parts prevents correct closing or opening of the finger assembly. When the clamps cannot release or re-engage properly the forming cycle stalls or produces a malformed tray, and the mechanism must be freed and reset before production can resume.

What is done about it

Inspect and replace worn clamp fingers, bushings or springs, verify alignment and free travel of the clamping assembly, and lubricate pivot points according to the maintenance plan. Review and adjust the clamp open/close timing and sensor calibration, and include the finger mechanism in preventive maintenance to detect wear before it causes stoppages.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.7% [0.2–1.9%]
Expected share of lost time
0.4% [0.1–1.1%]
Share of lost time when present
57% [47–67%]
Studies / units
112 / 155
Evidence grade
C

Grade C: 2 to 4 studies, or an interval wider than 0.35.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.8% [0.1–2.8%]14 studies
  • Soft drinks, bottled water and juices
    1.3% [0.2–3.7%]33 studies
  • Brewing, wine and spirits
    0.8% [0.1–2.6%]14 studies
  • Bakery and pasta
    0.9% [0.1–3.0%]6 studies
  • Meat, poultry and seafood
    0.9% [0.1–3.1%]6 studies
  • Fruit and vegetable processing
    0.9% [0.1–3.3%]4 studies
  • Grain and oilseed milling
    0.9% [0.1–3.0%]4 studies
  • Sugar and confectionery
    0.9% [0.1–3.3%]4 studies
  • Snacks, coffee, tea and other foods
    0.8% [0.1–3.0%]8 studies
  • Animal feed and pet food
    0.9% [0.1–2.9%]5 studies
  • Food manufacturing (unspecified or mixed)
    0.8% [0.1–2.7%]14 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The tray former uses a set of mechanical fingers or clamps to hold, fold and release the tray blank while it is shaped; wear, misalignment or jamming of these clamping parts prevents correct closing or opening of the finger assembly. When the clamps cannot release or re-engage properly the forming cycle stalls or produces a malformed tray, and the mechanism must be freed and reset before production can resume.

How it looks in SCADA data

Engineering guidance

MES/SCADA logs show the tray-forming station in fault or stopped state with clamp or finger position sensors outside their expected end-of-travel values, often paired with a cycle-fault or jam alarm specific to the forming axis. Repeated short stop codes on the same station, sometimes followed by a longer maintenance-type stop, indicate recurring clamp engagement or release problems.

Countermeasure

Engineering guidance

Inspect and replace worn clamp fingers, bushings or springs, verify alignment and free travel of the clamping assembly, and lubricate pivot points according to the maintenance plan. Review and adjust the clamp open/close timing and sensor calibration, and include the finger mechanism in preventive maintenance to detect wear before it causes stoppages.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Number of events: 82.0 events · as reported: “Tray forming system”
    Show verbatim quote
    จากการวิเคราะห์ข้อมูลในตารางที่ 3 พบว่าปัญหาหลักมาจากกลุ่มระบบจัดการขึ้นรูปถาด ซึ่งมีความถี่ความขัดข้องสูงถึง 82 ครั้ง คิดเป็นร้อยละ 65.60 ของปัญหาทั้งหมด
  2. Share of loss events: 65.6 % · as reported: “Tray forming system”
    Show verbatim quote
    จากการวิเคราะห์ข้อมูลในตารางที่ 3 พบว่าปัญหาหลักมาจากกลุ่มระบบจัดการขึ้นรูปถาด ซึ่งมีความถี่ความขัดข้องสูงถึง 82 ครั้ง คิดเป็นร้อยละ 65.60 ของปัญหาทั้งหมด
  3. Lost time: 10.0 min · as reported: “Releasing the finger parts clamping system”
    Show verbatim quote
    ปลดล็อคระบบจับยึด (Finger Parts) ในเครื่องพารามิเตอร์ 1 10