foratvise
Get Started
Equipment failure (breakdowns)

Tumbler shaft/body breakage

Equipment failure (breakdowns)AvailabilityMixing and blending

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 58 % of the line's lost time. Reported by 1 of the 31 studies that could observe it (sparse evidence).

What happens

Repeated cyclic torque and bending loads on the tumbler drive shaft, combined with product load imbalance, fatigue the shaft or structural welds until they fracture, causing the whole tumbler body or its drive shaft to break. Corrosion, wear of bearings or support bushings, and overloading beyond rated capacity accelerate the fatigue process and can trigger sudden catastrophic breakage.

What is done about it

Implement periodic non-destructive inspection (visual and ultrasonic/dye penetrant) of the shaft and welds, monitor vibration and torque trends to detect fatigue cracks before failure, and enforce load limits with balanced loading procedures. Replace shafts and bearings on a condition-based or preventive schedule using materials and dimensions rated for the actual operating loads.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
1.0% [0.2–3.1%]
Expected share of lost time
0.6% [0.1–1.8%]
Share of lost time when present
58% [47–68%]
Studies / units
31 / 40
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    1.1% [0.1–4.4%]6 studies
  • Soft drinks, bottled water and juices
    1.2% [0.1–4.8%]2 studies
  • Brewing, wine and spirits
    1.2% [0.1–4.8%]0 studies
  • Bakery and pasta
    1.1% [0.1–4.5%]2 studies
  • Meat, poultry and seafood
    1.8% [0.2–7.6%]1 study
  • Fruit and vegetable processing
    1.2% [0.1–4.8%]2 studies
  • Grain and oilseed milling
    1.2% [0.1–4.6%]0 studies
  • Sugar and confectionery
    1.2% [0.1–4.5%]3 studies
  • Snacks, coffee, tea and other foods
    1.2% [0.1–4.7%]3 studies
  • Animal feed and pet food
    1.1% [0.1–4.3%]5 studies
  • Food manufacturing (unspecified or mixed)
    1.2% [0.1–4.5%]7 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Repeated cyclic torque and bending loads on the tumbler drive shaft, combined with product load imbalance, fatigue the shaft or structural welds until they fracture, causing the whole tumbler body or its drive shaft to break. Corrosion, wear of bearings or support bushings, and overloading beyond rated capacity accelerate the fatigue process and can trigger sudden catastrophic breakage.

How it looks in SCADA data

Engineering guidance

Motor current or torque trace on the tumbler drive shows an abrupt spike followed by a drop to near zero or a sudden stop fault, often with a drive overcurrent or mechanical fault alarm. The machine state log shows an unplanned transition to stopped/fault state with no preceding slow-down trend, and downstream feed to the line is interrupted while upstream buffers fill.

Countermeasure

Engineering guidance

Implement periodic non-destructive inspection (visual and ultrasonic/dye penetrant) of the shaft and welds, monitor vibration and torque trends to detect fatigue cracks before failure, and enforce load limits with balanced loading procedures. Replace shafts and bearings on a condition-based or preventive schedule using materials and dimensions rated for the actual operating loads.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 33.0 min · as reported: “Tumbler breakage”
    Show verbatim quote
    Corrective maintenance time 33 min - 102 min - 40 min 20 min
  2. Lost time: 102 min · as reported: “Tumbler shaft breakage”
    Show verbatim quote
    Corrective maintenance time 33 min - 102 min - 40 min 20 min