foratvise
Get Started
Process defects (scrap and rework)

Underfill / short fill volume

Process defects (scrap and rework)QualityForming, moulding and depositing

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 47 % of the line's lost time. Reported by 2 of the 76 studies that could observe it (sparse evidence).

What happens

During blow-moulding/forming and filling of containers, the dosed or blown volume falls below the target specification because of worn dosing components, incorrect valve timing, pressure or temperature drift in the forming station, or variability in preform/parison wall thickness that changes the final container capacity. The result is finished units whose liquid or product content is below the declared or required volume, detected as a first-pass quality defect rather than a machine stoppage.

What is done about it

Calibrate and verify dosing valves, nozzles or volumetric cylinders against a reference standard, adjust forming pressure/temperature profiles to the preform specification, and tighten statistical process control limits on fill volume with automatic line stop or rework diversion when drift is detected. Preventive replacement of worn sealing and metering parts reduces recurrence.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.7% [0.1–2.1%]
Expected share of lost time
0.3% [0.1–1.0%]
Share of lost time when present
47% [35–59%]
Studies / units
76 / 96
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.8% [0.1–3.0%]5 studies
  • Soft drinks, bottled water and juices
    1.1% [0.1–4.2%]11 studies
  • Brewing, wine and spirits
    0.9% [0.1–3.4%]0 studies
  • Bakery and pasta
    0.7% [0.1–2.5%]25 studies
  • Meat, poultry and seafood
    0.9% [0.1–3.2%]3 studies
  • Fruit and vegetable processing
    0.8% [0.1–3.2%]3 studies
  • Grain and oilseed milling
    0.9% [0.1–3.2%]0 studies
  • Sugar and confectionery
    0.8% [0.1–2.9%]8 studies
  • Snacks, coffee, tea and other foods
    0.8% [0.1–3.0%]7 studies
  • Animal feed and pet food
    0.8% [0.1–3.1%]6 studies
  • Food manufacturing (unspecified or mixed)
    0.8% [0.1–3.1%]8 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

During blow-moulding/forming and filling of containers, the dosed or blown volume falls below the target specification because of worn dosing components, incorrect valve timing, pressure or temperature drift in the forming station, or variability in preform/parison wall thickness that changes the final container capacity. The result is finished units whose liquid or product content is below the declared or required volume, detected as a first-pass quality defect rather than a machine stoppage.

How it looks in SCADA data

Engineering guidance

MES/SCADA shows normal machine running states (no downtime event) combined with checkweigher or volume-sensor readings trending below the lower control limit, rising reject or downgrade counters on the inspection station, and recurring low-fill alarms without an associated stop code. Statistical process data (fill-volume trend charts) typically show a gradual drift rather than a step change.

Countermeasure

Engineering guidance

Calibrate and verify dosing valves, nozzles or volumetric cylinders against a reference standard, adjust forming pressure/temperature profiles to the preform specification, and tighten statistical process control limits on fill volume with automatic line stop or rework diversion when drift is detected. Preventive replacement of worn sealing and metering parts reduces recurrence.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Defect rate: 7.00 % · as reported: “Volume Kurang”
    Show verbatim quote
    Volume Kurang 24007 7% 96%
  2. Number of events: 24,007 units · as reported: “Volume Kurang”
    Show verbatim quote
    Volume Kurang | 24007 | 7% | 96%
  3. Share of loss events: 7.00 % · as reported: “Volume Kurang”
    Show verbatim quote
    Volume Kurang | 24007 | 7% | 96%