foratvise
Get Started
Idling and minor stops (micro-stops)

Discontinuous upstream feeding (hopper/conveyor bottleneck)

Idling and minor stops (micro-stops)PerformanceMilling and grinding

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 54 % of the line's lost time. Reported by 0 of the 43 studies that could observe it (sparse evidence).

What happens

The feed hopper and conveyor belt supplying the crusher do not deliver a steady, matched flow of material, so the crusher repeatedly runs starved or receives surges that it cannot process smoothly. This mismatch between upstream feed capacity and crusher throughput creates frequent short interruptions as the machine waits for material or clears uneven loads.

What is done about it

Add or resize a surge/buffer hopper upstream with level-based automatic control of the feeder and conveyor speed so that material supply matches crusher capacity continuously. Install belt or hopper level sensors interlocked with feeder speed control and schedule upstream logistics to avoid supply gaps.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.5% [0.1–1.6%]
Expected share of lost time
0.3% [0.0–0.9%]
Share of lost time when present
54% [42–66%]
Studies / units
43 / 48
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.0–2.5%]5 studies
  • Soft drinks, bottled water and juices
    0.6% [0.0–2.6%]1 study
  • Brewing, wine and spirits
    0.6% [0.0–2.5%]0 studies
  • Bakery and pasta
    0.6% [0.0–2.6%]0 studies
  • Meat, poultry and seafood
    0.6% [0.0–2.4%]0 studies
  • Fruit and vegetable processing
    0.6% [0.0–2.4%]2 studies
  • Grain and oilseed milling
    0.6% [0.0–2.4%]7 studies
  • Sugar and confectionery
    0.6% [0.0–2.4%]10 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.0–2.2%]5 studies
  • Animal feed and pet food
    0.6% [0.0–2.2%]6 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.0–2.4%]7 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The feed hopper and conveyor belt supplying the crusher do not deliver a steady, matched flow of material, so the crusher repeatedly runs starved or receives surges that it cannot process smoothly. This mismatch between upstream feed capacity and crusher throughput creates frequent short interruptions as the machine waits for material or clears uneven loads.

How it looks in SCADA data

Engineering guidance

SCADA shows the crusher run state cycling between running and idle in short bursts without any fault alarm, correlated with low or fluctuating hopper level readings and variable conveyor belt current/speed. Motor load on the crusher drops toward no-load values during starvation periods, and the pattern repeats intermittently rather than as a single sustained stop.

Countermeasure

Engineering guidance

Add or resize a surge/buffer hopper upstream with level-based automatic control of the feeder and conveyor speed so that material supply matches crusher capacity continuously. Install belt or hopper level sensors interlocked with feeder speed control and schedule upstream logistics to avoid supply gaps.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 193 min · as reported: “discontinuous plant feeding / bottleneck of hopper and conveyor belt”
    Show verbatim quote
    The time lost (193 min) was due to discontinuous plant feeding as batches of olive crop arrived in the mill, and then following the washing step, the bottleneck of a sole hopper and conveyor belt leading to the crushing machines.