Format/mould changeover on forming equipment
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei etwa 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 58 % der Verlustzeit der Linie. Berichtet von 3 der 76 Studien, die sie beobachten konnten (begrenzte Evidenz).
Was passiert
Switching the forming machine from one product or package format to another requires stopping production to remove and refit moulds, tooling or forming parts, reset dimensional and process parameters, and verify the first good units before resuming the run. The elapsed time between the last good unit of the previous format and the first good unit of the new one is lost to production.
Was man dagegen tut
Apply SMED methodology to separate internal from external setup activities, standardize and pre-stage tooling, use quick-change fixtures and locating features, and document a repeatable sequence so the forming machine can be reset with minimal stopped time.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 1,3 % [0,3–3,2 %]
- Erwarteter Anteil an der Verlustzeit
- 0,7 % [0,2–1,9 %]
- Anteil an der Verlustzeit bei Auftreten
- 58 % [46–68 %]
- Studien / Einheiten
- 76 / 96
- Evidenzgrad
- C
Grad C: 2 bis 4 Studien oder eine Intervallbreite über 0,35.
2Wahrscheinlichkeit nach Segment
- Milchprodukte2,1 % [0,3–7,4 %]5 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte1,3 % [0,2–4,5 %]11 Studien
- Bier, Wein und Spirituosen1,6 % [0,2–6,0 %]0 Studien
- Backwaren und Teigwaren1,6 % [0,3–4,7 %]25 Studien
- Fleisch, Geflügel und Fisch1,5 % [0,2–5,2 %]3 Studien
- Obst- und Gemüseverarbeitung1,5 % [0,2–5,1 %]3 Studien
- Getreide- und Ölsaatenmüllerei1,5 % [0,2–5,2 %]0 Studien
- Zucker und Süßwaren1,9 % [0,3–6,4 %]8 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel1,4 % [0,2–4,6 %]7 Studien
- Futtermittel und Heimtiernahrung1,4 % [0,2–4,7 %]6 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)1,4 % [0,2–4,6 %]8 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseSwitching the forming machine from one product or package format to another requires stopping production to remove and refit moulds, tooling or forming parts, reset dimensional and process parameters, and verify the first good units before resuming the run. The elapsed time between the last good unit of the previous format and the first good unit of the new one is lost to production.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseSCADA/MES shows a sustained non-running machine state tagged as changeover or setup, bracketed by the end of the prior production order and the start of the new one, with no fault alarms active; associated counters for mould or tooling changes and operator login events to the changeover procedure typically coincide with the stop.
Gegenmaßnahme
Ingenieurpraktische HinweiseApply SMED methodology to separate internal from external setup activities, standardize and pre-stage tooling, use quick-change fixtures and locating features, and document a repeatable sequence so the forming machine can be reset with minimal stopped time.
4Quellen
- CHANGEOVER TIME REDUCTION THROUGH LEAN TOOL “SMED” – A CASE STUDY FROM FOOD SECTOR (2018)Quelle öffnenMittlere Ereignisdauer: 210 min · laut Bericht: “changeover (selected type, average, long-run)”
Wörtliches Zitat anzeigen
The new changeover time was even lower than the project goal, but in the long run, the time was 210 minutes. This time is kept without any major problems.
- CHANGEOVER TIME REDUCTION THROUGH LEAN TOOL “SMED” – A CASE STUDY FROM FOOD SECTOR (2018)Quelle öffnenAnzahl der Ereignisse: 58,0 events/year · laut Bericht: “changeover (selected type, annual frequency)”
Wörtliches Zitat anzeigen
At a frequency of 58 changeovers per year and with a given number of operators and wage rates, the annual savings would be 91 thousand. CZK.
- CHANGEOVER TIME REDUCTION THROUGH LEAN TOOL “SMED” – A CASE STUDY FROM FOOD SECTOR (2018)Quelle öffnenMittlere Ereignisdauer: 244 min · laut Bericht: “changeover (selected type, average)”
Wörtliches Zitat anzeigen
The project team decided on the main goal of the project, which was to reduce the time of the selected sort by 10% of the average changeover time, from 244 minutes to 220 minutes.
- CHANGEOVER TIME REDUCTION THROUGH LEAN TOOL “SMED” – A CASE STUDY FROM FOOD SECTOR (2018)Quelle öffnenMittlere Ereignisdauer: 185 min · laut Bericht: “changeover (most frequent type)”
Wörtliches Zitat anzeigen
Of these types of changeovers, the fourth longest changeover was the most frequent (which would take 185 minutes), but the longest and second most frequent type of changeover (240 minutes) was eventually chosen by project team for the next step.
- CHANGEOVER TIME REDUCTION THROUGH LEAN TOOL “SMED” – A CASE STUDY FROM FOOD SECTOR (2018)Quelle öffnenMittlere Ereignisdauer: 240 min · laut Bericht: “changeover (selected type for SMED project)”
Wörtliches Zitat anzeigen
Of these types of changeovers, the fourth longest changeover was the most frequent (which would take 185 minutes), but the longest and second most frequent type of changeover (240 minutes) was eventually chosen by project team for the next step.
- CHANGEOVER TIME REDUCTION THROUGH LEAN TOOL “SMED” – A CASE STUDY FROM FOOD SECTOR (2018)Quelle öffnenMittlere Ereignisdauer: 194 min · laut Bericht: “changeover (selected type, average, first re-measurement)”
Wörtliches Zitat anzeigen
The average throw time dropped from 244 minutes to 194 minutes (Figure 7) and the target was met.
- CHANGEOVER TIME REDUCTION THROUGH LEAN TOOL “SMED” – A CASE STUDY FROM FOOD SECTOR (2018)Quelle öffnenMittlere Ereignisdauer: 4,00 min · laut Bericht: “Exchange of molds”
Wörtliches Zitat anzeigen
Exchange of molds: 0:04:00
- CHANGEOVER TIME REDUCTION THROUGH LEAN TOOL “SMED” – A CASE STUDY FROM FOOD SECTOR (2018)Quelle öffnenMittlere Ereignisdauer: 7,00 min · laut Bericht: “Forming of molds”
Wörtliches Zitat anzeigen
Forming of molds: 0:07:00
- Application of Lean-Total Productive Maintenance Tools to Reduce Setup Times and Machine Stoppages on the Molding Line of an SME in the Food Industry (2023)Quelle öffnenVerlustzeit: 280 min · laut Bericht: “Total duration of mold change”
Wörtliches Zitat anzeigen
From the data collection of the total duration of mold change times, a total of 280 minutes on average was obtained, and the times of internal activities, 254 min, and external activities, 26 min.
- Improvement Model for the Production Area to increase Labor Productivity through Lean Manufacturing tools in a bakery company (2026)Quelle öffnenVerlustzeit: 82,0 min · laut Bericht: “format changeovers (changing from circular to rectangular cookies)”
Wörtliches Zitat anzeigen
It was documented that the setup time averages 1.37 hours per day (82 minutes), consuming a significant portion of the available shift time.
- Improving Production Efficiency in a Chocolate SME through Continuous Flow, SMED and Poka-Yoke (2026)Quelle öffnenAnzahl der Ereignisse: 10,0 events/week · laut Bericht: “operational interruptions during mold changeover”
Wörtliches Zitat anzeigen
As-Is interruptions: 10 per week → 1 per week
- Improving Production Efficiency in a Chocolate SME through Continuous Flow, SMED and Poka-Yoke (2026)Quelle öffnenAnzahl der Ereignisse: 1,00 events/week · laut Bericht: “operational interruptions during mold changeover”
Wörtliches Zitat anzeigen
Week 5: 1 interruption
- Improving Production Efficiency in a Chocolate SME through Continuous Flow, SMED and Poka-Yoke (2026)Quelle öffnenAnzahl der Ereignisse: 5,00 events/week · laut Bericht: “operational interruptions during mold changeover”
Wörtliches Zitat anzeigen
Week 1: 5 interruptions
- Improving Production Efficiency in a Chocolate SME through Continuous Flow, SMED and Poka-Yoke (2026)Quelle öffnenAnzahl der Ereignisse: 3,00 events/week · laut Bericht: “operational interruptions during mold changeover”
Wörtliches Zitat anzeigen
Weeks 2, 3, and 4 stabilized at three interruptions each, showing improved workflow continuity and reduced operational stops.

