Minor stoppages on forming machines
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei etwa 2 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 52 % der Verlustzeit der Linie. Berichtet von 5 der 76 Studien, die sie beobachten konnten (gute Evidenz).
Was passiert
Forming equipment such as presses, manual moulding machines and blow moulders experience frequent brief stops caused by material misfeeds, mould or die sticking, blocked sensors, or parts that fail to eject or advance correctly. These interruptions are cleared quickly by the operator through manual intervention, resetting or clearing the obstruction, without requiring maintenance.
Was man dagegen tut
Apply autonomous maintenance routines with operator checklists for mould cleaning and feed guide adjustment, improve material feed and part ejection mechanisms, and standardise quick-clearance procedures to shorten each stoppage. Root-cause the most frequent fault codes to redesign the feed path or sensor placement and reduce recurrence.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 2,2 % [0,6–5,1 %]
- Erwarteter Anteil an der Verlustzeit
- 1,1 % [0,3–2,6 %]
- Anteil an der Verlustzeit bei Auftreten
- 52 % [40–62 %]
- Studien / Einheiten
- 76 / 96
- Evidenzgrad
- B
Grad B: 5 bis 9 Studien oder eine Intervallbreite zwischen 0,20 und 0,35.
2Wahrscheinlichkeit nach Segment
- Milchprodukte2,4 % [0,4–8,0 %]5 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte3,9 % [0,7–10,9 %]11 Studien
- Bier, Wein und Spirituosen2,6 % [0,4–8,6 %]0 Studien
- Backwaren und Teigwaren2,4 % [0,5–6,6 %]25 Studien
- Fleisch, Geflügel und Fisch3,7 % [0,6–12,7 %]3 Studien
- Obst- und Gemüseverarbeitung2,5 % [0,3–7,8 %]3 Studien
- Getreide- und Ölsaatenmüllerei2,6 % [0,4–8,8 %]0 Studien
- Zucker und Süßwaren2,2 % [0,3–7,0 %]8 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel2,2 % [0,3–6,9 %]7 Studien
- Futtermittel und Heimtiernahrung2,3 % [0,3–7,5 %]6 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)3,3 % [0,5–10,3 %]8 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseForming equipment such as presses, manual moulding machines and blow moulders experience frequent brief stops caused by material misfeeds, mould or die sticking, blocked sensors, or parts that fail to eject or advance correctly. These interruptions are cleared quickly by the operator through manual intervention, resetting or clearing the obstruction, without requiring maintenance.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseMES/SCADA logs show numerous short transitions to a stopped or idle machine state interspersed within otherwise running periods, with cycle or stroke counters showing gaps rather than continuous increments. Alarm history reveals repeated low-severity faults (feed, mould, sensor) that are acknowledged and cleared rapidly by the operator without a maintenance work order being generated.
Gegenmaßnahme
Ingenieurpraktische HinweiseApply autonomous maintenance routines with operator checklists for mould cleaning and feed guide adjustment, improve material feed and part ejection mechanisms, and standardise quick-clearance procedures to shorten each stoppage. Root-cause the most frequent fault codes to redesign the feed path or sensor placement and reduce recurrence.
4Quellen
- USULAN PENINGKATAN EFEKTIVITAS MESIN CETAK MANUAL MENGGUNAKAN METODE OVERALL EQUIPMENT EFFECTIVENESS (OEE) (STUDI KASUS DI PERUSAHAAN KERUPUK TTN) (2014)Quelle öffnenAnteil an der geplanten Zeit: 0,573 % · laut Bericht: “Idle and Minor Stoppage Losses”
Wörtliches Zitat anzeigen
= (240000−235754)𝑥 0,015 10200 = 0,573%
- ANALISIS PRODUKTIVITAS MESIN PRESS DENGAN PENDEKATAN OVERALL EQUIPMENT EFFECTIVENESS(OEE) PADAPT. JAPFA COMFEED INDONESIA LAMPUNG (2017)Quelle öffnenAnteil an der Verlustzeit: 2,50 % · laut Bericht: “Idling & minor stoppages losses”
Wörtliches Zitat anzeigen
Idling & minor stoppages losses 8,30 2,50 97,39
- ANALISIS PRODUKTIVITAS MESIN PRESS DENGAN PENDEKATAN OVERALL EQUIPMENT EFFECTIVENESS(OEE) PADAPT. JAPFA COMFEED INDONESIA LAMPUNG (2017)Quelle öffnenVerlustzeit: 8,30 jam · laut Bericht: “Idling & minor stoppages losses”
Wörtliches Zitat anzeigen
Idling & minor stoppages losses 8,30 2,50 97,39
- ANALYSIS OF THE OVERALL EQUIPMENT EFFECTIVENESS TO MINIMIZE SIX BIG LOSSES OF COOKIE CAPPER MACHINE-A CASE STUDY IN MANUFACTURING INDUSTRY (2020)Quelle öffnenAnteil an der Verlustzeit: 10,6 % · laut Bericht: “Minor stoppage”
Wörtliches Zitat anzeigen
Minor stoppage 6.30% 10.40% 15.00% 10.56%
- Anteil an der Verlustzeit: 24,6 % · laut Bericht: “idling & minor stoppages losses”
Wörtliches Zitat anzeigen
the three biggest factors that caused the low value of machine effectiveness were idling & minor stoppages losses of 24.61%, yield losses of 24.37%, and reduced speed losses of 23.78%
- Measuring the Efficiency of Contiform Machines with the Overall Equipment Effectiveness Method at PT Tirta Investama Pandaan (2025)Quelle öffnenAnteil an der Verlustzeit: 29,8 % · laut Bericht: “Idle Minor Stoppage”
Wörtliches Zitat anzeigen
The Six Big Losses analysis identified the two most dominant major losses, namely idle minor stoppage of 29.82% and reduce speed of 13.53%.
- Analisis Total Productive Maintenance (TPM) dengan Menggunakan Metode Overall Equipment Effectiveness (OEE) pada Mesin Blowing (2025)Quelle öffnenAnteil an der Verlustzeit: 11,5 % · laut Bericht: “Idling & Minor Stoppage Losses”
Wörtliches Zitat anzeigen
Rata - rata 6,10 0,95 11,47 0,00 0,00 0,21
- Improving press machine efficiency using a TPM approach and Six Big Losses analysis (2025)Quelle öffnenAnteil an der Verlustzeit: 48,0 % · laut Bericht: “idling and minor stoppages”
Wörtliches Zitat anzeigen
The primary causes of low efficiency are idling and minor stoppages (48%) and equipment failures (28%), both of which are influenced by a lack of preventive maintenance and errors in machine settings.

