foratvise
Get Started
Process defects (scrap and rework)

Excess air entrapped in sealed bag

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 48 % of the line's lost time. Reported by 0 of the 112 studies that could observe it (sparse evidence).

What happens

During bag forming and sealing, insufficient evacuation of headspace or inconsistent product dosing allows a larger than intended pocket of air to remain inside the bag before the final seal is made. The trapped air gives the pack an abnormal shape, apparent underfill, or reduced shelf stability, so the unit fails inspection at first pass.

What is done about it

Verify and recalibrate the vacuum or air-evacuation step prior to sealing, check for leaks or wear in the evacuation nozzle and bag-forming jaws, and tune dosing timing to avoid introducing extra air with the product. Reinforce in-process checks on headspace and seal quality to catch drift before it propagates to many packs.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.4% [0.1–1.2%]
Expected share of lost time
0.2% [0.0–0.6%]
Share of lost time when present
48% [36–59%]
Studies / units
112 / 155
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.4% [0.0–1.7%]14 studies
  • Soft drinks, bottled water and juices
    0.4% [0.0–1.5%]33 studies
  • Brewing, wine and spirits
    0.4% [0.0–1.6%]14 studies
  • Bakery and pasta
    0.4% [0.0–1.8%]6 studies
  • Meat, poultry and seafood
    0.5% [0.0–1.8%]6 studies
  • Fruit and vegetable processing
    0.5% [0.0–1.8%]4 studies
  • Grain and oilseed milling
    0.5% [0.0–1.7%]4 studies
  • Sugar and confectionery
    0.5% [0.0–1.9%]4 studies
  • Snacks, coffee, tea and other foods
    0.4% [0.0–1.7%]8 studies
  • Animal feed and pet food
    0.5% [0.0–1.8%]5 studies
  • Food manufacturing (unspecified or mixed)
    0.4% [0.0–1.7%]14 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

During bag forming and sealing, insufficient evacuation of headspace or inconsistent product dosing allows a larger than intended pocket of air to remain inside the bag before the final seal is made. The trapped air gives the pack an abnormal shape, apparent underfill, or reduced shelf stability, so the unit fails inspection at first pass.

How it looks in SCADA data

Engineering guidance

Vision inspection or checkweigher systems flag rejects for abnormal pack shape, headspace, or weight variance without any associated machine fault or stoppage. Vacuum or evacuation pressure traces on the sealing station show deviations from setpoint during the cycles that correspond to rejected bags, while sealing time and temperature remain within normal range.

Countermeasure

Engineering guidance

Verify and recalibrate the vacuum or air-evacuation step prior to sealing, check for leaks or wear in the evacuation nozzle and bag-forming jaws, and tune dosing timing to avoid introducing extra air with the product. Reinforce in-process checks on headspace and seal quality to catch drift before it propagates to many packs.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Defect rate: 17.0 % · as reported: “bag with extra air”
    Show verbatim quote
    % of lots rejected due to bag with extra air | 17%
  2. Defect rate: 15.0 % · as reported: “bag with extra air”
    Show verbatim quote
    % of lots rejected due to bag with extra air | 15%