foratvise
Get Started
Equipment failure (breakdowns)

Belt drive / transmission shaft failure

Equipment failure (breakdowns)AvailabilityMilling and grinding

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 58 % of the line's lost time. Reported by 1 of the 43 studies that could observe it (sparse evidence).

What happens

The belt drive transmits rotary power from the motor to the milling rolls or shaft; wear, misalignment, excessive tension, fatigue or contamination causes the belt to crack, slip or snap, and the associated transmission shaft or belt cover can crack or deform under the same stresses. Loss of power transmission stops or degrades the mill until the belt, shaft or cover is repaired or replaced.

What is done about it

Apply condition-based maintenance with periodic belt tension, alignment and wear inspection, vibration and thermal monitoring of the drive shaft, and scheduled replacement of belts, shafts and covers based on condition rather than failure; protect the belt cover from impact and keep it properly guarded.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.9% [0.2–2.7%]
Expected share of lost time
0.5% [0.1–1.6%]
Share of lost time when present
58% [47–68%]
Studies / units
43 / 48
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    1.1% [0.1–4.3%]5 studies
  • Soft drinks, bottled water and juices
    1.1% [0.1–4.4%]1 study
  • Brewing, wine and spirits
    1.1% [0.1–4.4%]0 studies
  • Bakery and pasta
    1.1% [0.1–4.4%]0 studies
  • Meat, poultry and seafood
    1.1% [0.1–4.6%]0 studies
  • Fruit and vegetable processing
    1.1% [0.1–4.4%]2 studies
  • Grain and oilseed milling
    1.1% [0.1–4.1%]7 studies
  • Sugar and confectionery
    1.0% [0.1–3.9%]10 studies
  • Snacks, coffee, tea and other foods
    1.5% [0.2–5.7%]5 studies
  • Animal feed and pet food
    1.1% [0.1–4.3%]6 studies
  • Food manufacturing (unspecified or mixed)
    1.1% [0.1–3.9%]7 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The belt drive transmits rotary power from the motor to the milling rolls or shaft; wear, misalignment, excessive tension, fatigue or contamination causes the belt to crack, slip or snap, and the associated transmission shaft or belt cover can crack or deform under the same stresses. Loss of power transmission stops or degrades the mill until the belt, shaft or cover is repaired or replaced.

How it looks in SCADA data

Engineering guidance

SCADA/MES shows a motor-running or drive-fault alarm with the mill in a stopped or fault state, often preceded by rising motor current, torque or vibration trend on the drive shaft and a drop in mill output or roll speed to zero; equipment-failure stop code is logged with maintenance intervention required to clear it.

Countermeasure

Engineering guidance

Apply condition-based maintenance with periodic belt tension, alignment and wear inspection, vibration and thermal monitoring of the drive shaft, and scheduled replacement of belts, shafts and covers based on condition rather than failure; protect the belt cover from impact and keep it properly guarded.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Time between events: 1,685 Hr · as reported: “Drive related failures”
    Show verbatim quote
    Drive related failures 1685.17 6.83 - -
  2. Lost time: 1.25 Hr · as reported: “V1: Belt drive cover damaged”
    Show verbatim quote
    02/22/16 015173 V1: Belt drive cover damaged CMP 0.75 0.5 1.25
  3. Mean event duration: 6.83 Hr · as reported: “Drive related failures”
    Show verbatim quote
    Drive related failures 1685.17 6.83 - -
  4. Lost time: 20.5 hours · as reported: “belt failure, transmission shaft failure, minor belt cover damage”
    Show verbatim quote
    The belt driven V1 has experienced belt failure, transmission shaft failure, and minor belt cover damage, resulting in a total stoppage of 20.5 hours.