foratvise
Get Started
Equipment failure (breakdowns)

Blower malfunction

Equipment failure (breakdowns)AvailabilityUtilities (steam, compressed air, chilled water, power)

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 58 % of the line's lost time. Reported by 0 of the 131 studies that could observe it (sparse evidence).

What happens

A blower (air/fan unit) supplying pressurized air or airflow for drying, cooling, pneumatic conveying or bottle handling degrades or fails due to bearing wear, motor overload, belt breakage, impeller imbalance or filter/duct clogging. The resulting drop in airflow or pressure interrupts the dependent process step, either tripping the unit outright or forcing brief operator-cleared stops.

What is done about it

Apply a preventive maintenance program covering bearing lubrication, belt tension checks, impeller balancing and periodic filter or duct cleaning, supported by vibration and current monitoring to detect degradation before failure. Where the blower is critical to line continuity, provide a standby unit or redundant airflow path to avoid full line stoppage.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.4% [0.1–1.1%]
Expected share of lost time
0.2% [0.0–0.6%]
Share of lost time when present
58% [46–68%]
Studies / units
131 / 165
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.4% [0.0–1.7%]13 studies
  • Soft drinks, bottled water and juices
    0.4% [0.0–1.5%]26 studies
  • Brewing, wine and spirits
    0.4% [0.0–1.7%]12 studies
  • Bakery and pasta
    0.4% [0.0–1.4%]25 studies
  • Meat, poultry and seafood
    0.5% [0.0–1.8%]9 studies
  • Fruit and vegetable processing
    0.5% [0.0–1.8%]7 studies
  • Grain and oilseed milling
    0.4% [0.0–1.7%]7 studies
  • Sugar and confectionery
    0.4% [0.0–1.8%]9 studies
  • Snacks, coffee, tea and other foods
    0.4% [0.0–1.7%]5 studies
  • Animal feed and pet food
    0.5% [0.0–1.8%]7 studies
  • Food manufacturing (unspecified or mixed)
    0.5% [0.0–1.8%]11 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

A blower (air/fan unit) supplying pressurized air or airflow for drying, cooling, pneumatic conveying or bottle handling degrades or fails due to bearing wear, motor overload, belt breakage, impeller imbalance or filter/duct clogging. The resulting drop in airflow or pressure interrupts the dependent process step, either tripping the unit outright or forcing brief operator-cleared stops.

How it looks in SCADA data

Engineering guidance

Blower run-status changes to fault or stopped, motor current or vibration signal exceeds alarm limits, airflow/pressure transmitter reading drops below setpoint, and downstream equipment shows starvation or blocking states correlated with the blower fault timestamp. Short, frequent fault-reset cycles appear when the issue is intermittent rather than a hard trip.

Countermeasure

Engineering guidance

Apply a preventive maintenance program covering bearing lubrication, belt tension checks, impeller balancing and periodic filter or duct cleaning, supported by vibration and current monitoring to detect degradation before failure. Where the blower is critical to line continuity, provide a standby unit or redundant airflow path to avoid full line stoppage.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 278 min · as reported: “Blower”
    Show verbatim quote
    Operational losses (min) | 278 | 494 | 106 | 53 | 157 | 1088 | 48
  2. Lost time: 420 min · as reported: “Blower”
    Show verbatim quote
    Equipment losses (min) | 420 | 364 | 24 | 55 | 152 | 1015 | 44.8