foratvise
Get Started
Idling and minor stops (micro-stops)

Bottle jam on spiral infeed screw

Idling and minor stops (micro-stops)PerformanceFilling

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 52 % of the line's lost time. Reported by 0 of the 120 studies that could observe it (sparse evidence).

What happens

The rotating spiral (worm) screw that spaces and guides incoming bottles toward the filling stations can trap, tilt or wedge a container when it is misaligned, deformed, oversized or arrives with an irregular pitch relative to the thread. The bottle becomes physically obstructed between the screw flights and the guide rail, stopping its forward progression and blocking the infeed path for following containers.

What is done about it

Operator clears the jammed bottle manually and restarts the infeed; preventive actions include verifying bottle dimensional tolerances, adjusting screw pitch/guide rail clearance, and performing routine alignment and wear inspection of the spiral drive.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.3% [0.1–1.0%]
Expected share of lost time
0.2% [0.0–0.5%]
Share of lost time when present
52% [40–64%]
Studies / units
120 / 162
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.4% [0.0–1.5%]18 studies
  • Soft drinks, bottled water and juices
    0.3% [0.0–1.2%]44 studies
  • Brewing, wine and spirits
    0.4% [0.0–1.5%]16 studies
  • Bakery and pasta
    0.4% [0.0–1.7%]0 studies
  • Meat, poultry and seafood
    0.4% [0.0–1.6%]6 studies
  • Fruit and vegetable processing
    0.4% [0.0–1.6%]4 studies
  • Grain and oilseed milling
    0.4% [0.0–1.6%]6 studies
  • Sugar and confectionery
    0.4% [0.0–1.6%]3 studies
  • Snacks, coffee, tea and other foods
    0.4% [0.0–1.5%]6 studies
  • Animal feed and pet food
    0.4% [0.0–1.7%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.4% [0.0–1.5%]13 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The rotating spiral (worm) screw that spaces and guides incoming bottles toward the filling stations can trap, tilt or wedge a container when it is misaligned, deformed, oversized or arrives with an irregular pitch relative to the thread. The bottle becomes physically obstructed between the screw flights and the guide rail, stopping its forward progression and blocking the infeed path for following containers.

How it looks in SCADA data

Engineering guidance

SCADA/MES shows a short machine microstop or infeed-sensor fault code with very brief duration, often paired with a photoeye or proximity sensor at the spiral section reporting a continuous blocked state until operator clearance. Downstream filling valves may show starvation while upstream conveyors show blocking/back-up accumulation during the event.

Countermeasure

Engineering guidance

Operator clears the jammed bottle manually and restarts the infeed; preventive actions include verifying bottle dimensional tolerances, adjusting screw pitch/guide rail clearance, and performing routine alignment and wear inspection of the spiral drive.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Number of events: 2.00 events · as reported: “Bottle obstruted on spiral drive”
    Show verbatim quote
    7 Bottle obstruted on spiral drive 2 61 100%