Equipment calibration/adjustment error
In short
It appears in about 1 of every 100 lines studied.
When it appears, it takes on average about 57 % of the line's lost time. Reported by 2 of the 127 studies that could observe it (limited evidence).
What happens
An operator or technician sets machine parameters, sensors or mechanical references incorrectly during changeover or routine adjustment, often because the task was assigned to personnel without the right skill or because no standard procedure was followed. The resulting mis-calibration leaves the equipment running outside its intended operating window, so the line stops or must be readjusted before stable production resumes.
What is done about it
Define and enforce standardized calibration/adjustment procedures with checklists and reference setpoints, assign the task only to trained and qualified personnel, and use quick-set tools or automated calibration routines to reduce dependence on manual judgement. Verify setup against a reference standard before releasing the line to run.
Practical guidance written from engineering knowledge; it is not a statistical estimate.
1Probability and evidence
- Probability of presence
- 0.7% [0.2–1.7%]
- Expected share of lost time
- 0.4% [0.1–1.0%]
- Share of lost time when present
- 57% [44–67%]
- Studies / units
- 127 / 161
- Evidence grade
- C
Grade C: 2 to 4 studies, or an interval wider than 0.35.
2Probability by segment
- Dairy products0.8% [0.1–2.7%]13 studies
- Soft drinks, bottled water and juices0.7% [0.1–2.2%]26 studies
- Brewing, wine and spirits0.8% [0.1–2.7%]11 studies
- Bakery and pasta1.0% [0.1–3.1%]24 studies
- Meat, poultry and seafood0.8% [0.1–2.7%]9 studies
- Fruit and vegetable processing0.8% [0.1–3.0%]7 studies
- Grain and oilseed milling0.8% [0.1–2.9%]6 studies
- Sugar and confectionery0.8% [0.1–2.5%]9 studies
- Snacks, coffee, tea and other foods1.1% [0.1–3.8%]5 studies
- Animal feed and pet food0.8% [0.1–2.8%]7 studies
- Food manufacturing (unspecified or mixed)0.8% [0.1–2.8%]10 studies
3Mechanism, SCADA signature and countermeasure
Mechanism
Engineering guidanceAn operator or technician sets machine parameters, sensors or mechanical references incorrectly during changeover or routine adjustment, often because the task was assigned to personnel without the right skill or because no standard procedure was followed. The resulting mis-calibration leaves the equipment running outside its intended operating window, so the line stops or must be readjusted before stable production resumes.
How it looks in SCADA data
Engineering guidanceExtended time in setup/adjustment or minor-stop machine states right after a changeover or shift handover, repeated short stops with the same alarm code, or parameter values (position, pressure, speed, timing) drifting outside tolerance bands recorded by the control system. Correlated starvation/blocking of upstream or downstream stations often follows the affected unit.
Countermeasure
Engineering guidanceDefine and enforce standardized calibration/adjustment procedures with checklists and reference setpoints, assign the task only to trained and qualified personnel, and use quick-set tools or automated calibration routines to reduce dependence on manual judgement. Verify setup against a reference standard before releasing the line to run.
4Sources
- Proposal to improve efficiency in pre-baked bread production lines in a Peruvian SME, using SMED and TPM (2025)Open sourceLost time: 17.0 h · as reported: “Error en calibración/ajuste del equipo”
Show verbatim quote
Error en calibracion/ajuste del equipo 16.95 16%
- Proposal to improve efficiency in pre-baked bread production lines in a Peruvian SME, using SMED and TPM (2025)Open sourceShare of lost time: 16.0 % · as reported: “Error en calibración/ajuste del equipo”
Show verbatim quote
Error en calibracion/ajuste del equipo 16.95 16%
- Propuesta de mejora para incrementar el rendimiento de la línea de salsas usando SMED, Kanban, Industria 4.0 y 5S en una empresa del sector alimenticio (2026)Open sourceShare of lost time: 2.29 % · as reported: “Deficiente calibración de equipos”
Show verbatim quote
Deficiente calibración de equipos 533.28 2.29% 96.63%
- Propuesta de mejora para incrementar el rendimiento de la línea de salsas usando SMED, Kanban, Industria 4.0 y 5S en una empresa del sector alimenticio (2026)Open sourceLost time: 533 min · as reported: “Deficiente calibración de equipos”
Show verbatim quote
Deficiente calibración de equipos 533.28 2.29% 96.63%
- Propuesta de mejora para incrementar el rendimiento de la línea de salsas usando SMED, Kanban, Industria 4.0 y 5S en una empresa del sector alimenticio (2026)Open sourceShare of lost time: 21.0 % · as reported: “Deficiente asignación de tareas”
Show verbatim quote
Deficiente asignación de tareas 4886.52 21.02% 60.87%
- Propuesta de mejora para incrementar el rendimiento de la línea de salsas usando SMED, Kanban, Industria 4.0 y 5S en una empresa del sector alimenticio (2026)Open sourceLost time: 4,887 min · as reported: “Deficiente asignación de tareas”
Show verbatim quote
Deficiente asignación de tareas 4886.52 21.02% 60.87%

