foratvise
Get Started
Process defects (scrap and rework)

Aseptic carton form-fill-seal defect

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 48 % of the line's lost time. Reported by 0 of the 112 studies that could observe it (sparse evidence).

What happens

On form-fill-seal carton packaging units, defects originate from misaligned packaging material, incorrect longitudinal or transversal seal temperature and pressure, or contamination of the seal area by product, producing cartons with leaks, malformed shape or weak seals that fail specification. These nonconforming units are detected during stable production rather than causing a full stop of the line.

What is done about it

Apply preventive calibration and condition monitoring of sealing jaws, induction or ultrasonic sealing elements and material tracking rollers, verify packaging material quality and alignment at reel changeovers, and use statistical process control on seal strength and fill weight to detect drift before defect rate rises.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.4% [0.1–1.1%]
Expected share of lost time
0.2% [0.0–0.5%]
Share of lost time when present
48% [36–60%]
Studies / units
112 / 155
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.4% [0.0–1.7%]14 studies
  • Soft drinks, bottled water and juices
    0.4% [0.0–1.3%]33 studies
  • Brewing, wine and spirits
    0.4% [0.0–1.7%]14 studies
  • Bakery and pasta
    0.4% [0.0–1.6%]6 studies
  • Meat, poultry and seafood
    0.4% [0.0–1.8%]6 studies
  • Fruit and vegetable processing
    0.4% [0.0–1.7%]4 studies
  • Grain and oilseed milling
    0.4% [0.0–1.9%]4 studies
  • Sugar and confectionery
    0.4% [0.0–1.8%]4 studies
  • Snacks, coffee, tea and other foods
    0.4% [0.0–1.6%]8 studies
  • Animal feed and pet food
    0.4% [0.0–1.7%]5 studies
  • Food manufacturing (unspecified or mixed)
    0.4% [0.0–1.6%]14 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

On form-fill-seal carton packaging units, defects originate from misaligned packaging material, incorrect longitudinal or transversal seal temperature and pressure, or contamination of the seal area by product, producing cartons with leaks, malformed shape or weak seals that fail specification. These nonconforming units are detected during stable production rather than causing a full stop of the line.

How it looks in SCADA data

Engineering guidance

MES/SCADA logs show elevated reject counts at the downstream inspection or leak-test station tagged to the carton unit, with specific defect codes for seal failure, misformed package or fill-level deviation, while the machine state remains in run without triggering a stop alarm. Seal temperature or jaw-pressure trend signals may drift outside setpoint band coinciding with the reject spikes.

Countermeasure

Engineering guidance

Apply preventive calibration and condition monitoring of sealing jaws, induction or ultrasonic sealing elements and material tracking rollers, verify packaging material quality and alignment at reel changeovers, and use statistical process control on seal strength and fill weight to detect drift before defect rate rises.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 83.0 Minutes · as reported: “Tetra Pak unit”
    Show verbatim quote
    Tetra Pak unit 83 Defects, rework, over processing