foratvise
Get Started
Equipment failure (breakdowns)

Jam/blockage at coding or sealing station

Equipment failure (breakdowns)AvailabilityFilling

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 0 of the 120 studies that could observe it (sparse evidence).

What happens

Packaging material, product residue or a misaligned component becomes physically lodged in the coding head or the sealing jaws, preventing the mechanism from cycling and forcing the station into a blocked state. The obstruction is usually mechanical rather than a control fault, so the line stops until the blockage is manually cleared and the mechanism is reset.

What is done about it

Clear the physical obstruction, inspect and realign the coding head or sealing jaws, and verify material feed guides and tension settings. Implement a preventive maintenance routine to check wear parts and sensor cleanliness at these stations to reduce recurrence of blockages.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.4% [0.1–1.1%]
Expected share of lost time
0.2% [0.0–0.6%]
Share of lost time when present
57% [46–67%]
Studies / units
120 / 162
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.4% [0.0–1.6%]18 studies
  • Soft drinks, bottled water and juices
    0.4% [0.0–1.3%]44 studies
  • Brewing, wine and spirits
    0.4% [0.0–1.5%]16 studies
  • Bakery and pasta
    0.5% [0.0–1.9%]0 studies
  • Meat, poultry and seafood
    0.5% [0.0–1.9%]6 studies
  • Fruit and vegetable processing
    0.5% [0.0–1.7%]4 studies
  • Grain and oilseed milling
    0.5% [0.0–1.8%]6 studies
  • Sugar and confectionery
    0.5% [0.0–1.8%]3 studies
  • Snacks, coffee, tea and other foods
    0.5% [0.0–1.7%]6 studies
  • Animal feed and pet food
    0.5% [0.0–1.8%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.4% [0.0–1.7%]13 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Packaging material, product residue or a misaligned component becomes physically lodged in the coding head or the sealing jaws, preventing the mechanism from cycling and forcing the station into a blocked state. The obstruction is usually mechanical rather than a control fault, so the line stops until the blockage is manually cleared and the mechanism is reset.

How it looks in SCADA data

Engineering guidance

The coding or sealing station reports a fault or blocked-state alarm, the machine status transitions to stopped with the specific station flagged, and cycle counters freeze while upstream stations continue running, causing blocking of upstream equipment and starvation downstream. Repeated short bursts of the same alarm code at that station are typical before a full stoppage.

Countermeasure

Engineering guidance

Clear the physical obstruction, inspect and realign the coding head or sealing jaws, and verify material feed guides and tension settings. Implement a preventive maintenance routine to check wear parts and sensor cleanliness at these stations to reduce recurrence of blockages.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Number of events: 1.00 events · as reported: “Block Sealing”
    Show verbatim quote
    Block Sealing 1
  2. Number of events: 5.00 events · as reported: “Block Coding”
    Show verbatim quote
    Block Coding 5