foratvise
Get Started
Idling and minor stops (micro-stops)

Container jam at bottle divider/lane splitter

Idling and minor stops (micro-stops)PerformanceFilling

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 53 % of the line's lost time. Reported by 1 of the 120 studies that could observe it (sparse evidence).

What happens

A bottle becomes wedged or tips over as it passes through the mechanical divider that splits a single infeed lane into multiple lanes (or merges lanes) ahead of the filler, usually due to slight misalignment of guide rails, worn divider screws or belts, or an out-of-spec container geometry. The stuck bottle blocks the passage and causes following containers to back up against it.

What is done about it

Realign and periodically inspect divider guide rails, screws and star wheels for wear, verify container dimensional tolerances against the divider setting, and add sensors or sweep mechanisms to detect and clear jams automatically before they propagate upstream or downstream.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.5% [0.1–1.4%]
Expected share of lost time
0.3% [0.1–0.7%]
Share of lost time when present
53% [40–64%]
Studies / units
120 / 162
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.5% [0.1–1.9%]18 studies
  • Soft drinks, bottled water and juices
    0.7% [0.1–2.1%]44 studies
  • Brewing, wine and spirits
    0.5% [0.1–1.9%]16 studies
  • Bakery and pasta
    0.6% [0.1–2.5%]0 studies
  • Meat, poultry and seafood
    0.6% [0.1–2.1%]6 studies
  • Fruit and vegetable processing
    0.6% [0.1–2.1%]4 studies
  • Grain and oilseed milling
    0.6% [0.1–2.1%]6 studies
  • Sugar and confectionery
    0.6% [0.1–2.2%]3 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.1–2.1%]6 studies
  • Animal feed and pet food
    0.6% [0.1–2.1%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.1–2.1%]13 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

A bottle becomes wedged or tips over as it passes through the mechanical divider that splits a single infeed lane into multiple lanes (or merges lanes) ahead of the filler, usually due to slight misalignment of guide rails, worn divider screws or belts, or an out-of-spec container geometry. The stuck bottle blocks the passage and causes following containers to back up against it.

How it looks in SCADA data

Engineering guidance

Short machine-state stop or micro-stop on the divider/filler with no fault code requiring maintenance, often paired with a photocell or proximity sensor stuck in the blocked state and a rise in upstream conveyor accumulation; downstream filler shows starvation while upstream conveying shows blocking. Stop is cleared manually by the operator without a work order.

Countermeasure

Engineering guidance

Realign and periodically inspect divider guide rails, screws and star wheels for wear, verify container dimensional tolerances against the divider setting, and add sensors or sweep mechanisms to detect and clear jams automatically before they propagate upstream or downstream.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 322 min · as reported: “bottle stuck in the SIPA divider”
    Show verbatim quote
    In the month February – May 2019 recorded existence minor idling downtime stop at line 4 , namely , CIP ( Cleaning In Place ) 2,509 minutes , SIP ( Sanitation In Place ) 1,943 minutes , stuck stamp on track 484 minutes , bottle stuck in the SIPA 322 divider , tilting was stuck for 277 minutes and the pallet ran out for 93 minutes .