foratvise
Get Started
Equipment failure (breakdowns)

Control instrument misalignment

Equipment failure (breakdowns)AvailabilitySterilization (retort, UHT)

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 1 of the 34 studies that could observe it (sparse evidence).

What happens

Sensors or control elements that regulate temperature, pressure or valve position on the autoclave drift out of calibration or become physically misaligned, so the readings or actuator feedback no longer match the actual process state. This forces the control loop to act on erroneous signals, driving the sterilization cycle outside its validated parameters until the equipment is stopped for correction.

What is done about it

Apply a scheduled calibration and verification program for temperature, pressure and valve-position instruments, including cross-checks against reference standards and physical inspection of sensor mounting and linkage alignment. Use redundant or independent measurement points with automated deviation alarms to detect drift before it affects cycle validity.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
1.1% [0.2–3.3%]
Expected share of lost time
0.6% [0.1–1.9%]
Share of lost time when present
57% [46–67%]
Studies / units
34 / 37
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    1.2% [0.1–4.8%]5 studies
  • Soft drinks, bottled water and juices
    1.2% [0.1–4.8%]2 studies
  • Brewing, wine and spirits
    1.2% [0.1–4.9%]1 study
  • Bakery and pasta
    1.3% [0.1–5.3%]0 studies
  • Meat, poultry and seafood
    1.8% [0.2–7.6%]1 study
  • Fruit and vegetable processing
    1.3% [0.1–5.1%]2 studies
  • Grain and oilseed milling
    1.2% [0.1–4.6%]6 studies
  • Sugar and confectionery
    1.2% [0.1–4.6%]3 studies
  • Snacks, coffee, tea and other foods
    1.2% [0.1–5.0%]3 studies
  • Animal feed and pet food
    1.2% [0.1–4.4%]4 studies
  • Food manufacturing (unspecified or mixed)
    1.2% [0.1–4.5%]7 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Sensors or control elements that regulate temperature, pressure or valve position on the autoclave drift out of calibration or become physically misaligned, so the readings or actuator feedback no longer match the actual process state. This forces the control loop to act on erroneous signals, driving the sterilization cycle outside its validated parameters until the equipment is stopped for correction.

How it looks in SCADA data

Engineering guidance

SCADA shows persistent deviation or offset between redundant or cross-checked sensor readings, out-of-range alarms on temperature or pressure channels, and control output saturating without the process variable responding as expected. The autoclave state log registers an unplanned stop in fault or maintenance mode tied to an instrument or control-loop alarm.

Countermeasure

Engineering guidance

Apply a scheduled calibration and verification program for temperature, pressure and valve-position instruments, including cross-checks against reference standards and physical inspection of sensor mounting and linkage alignment. Use redundant or independent measurement points with automated deviation alarms to detect drift before it affects cycle validity.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Number of events: 5.00 occurrences/month · as reported: “Control instrument misalignment”
    Show verbatim quote
    Control instrument misalignment 5 40 3.2
  2. Share of planned time: 3.20 % · as reported: “Control instrument misalignment”
    Show verbatim quote
    Control instrument misalignment 5 40 3.2
  3. Mean event duration: 40.0 min · as reported: “Control instrument misalignment”
    Show verbatim quote
    Control instrument misalignment 5 40 3.2