Sterilization (retort, UHT)
In-container sterilisation of a conduction-heating low-acid canned food (batch steam retort)
In short
Sterilization (retort, UHT) can use at most 89 of every 100 planned hours. The rest goes to limits no plant can avoid.
- 89usable at most
- 11are a physical limit
The three limits that set it
Running time: up to 96 %
The rest are stops imposed by physics or by regulation: cleaning, changeovers, defrosting.
Speed: up to 93 %
How close to its maximum speed it can run without damaging the product or the equipment.
Good product: up to 100 %
Some product falls outside specification even with the process well under control.
Technical detail
Uncertainty intervals, physical models per station and sources, for anyone who wants to check each figure.
1Scenario
Solid-pack fish (tuna-style) in 84 × 46.5 mm cans is sterilised in a batch retort with saturated steam at 121.1 °C. The retort is loaded, vented to remove air, held at processing temperature until the slowest-heating point of every can (its geometric centre, since the pack heats by conduction) has received the required lethality, and cooled with water until the centre falls to the unloading temperature. The variant of continuous ultra-high-temperature (UHT) treatment of pumpable products followed by aseptic filling uses the same kinetics with a thin-film heating step instead of conduction into a can; it is described in the derivation but not computed here.
2Results
- TheoreticalThermodynamic minimum heat (product returns to ambient)0 kJ/kg
- Sensible heat of product and container without heat recovery313 [239–368] kJ/kg
- Best available techniqueState-of-the-art on-site energy of retort sterilisation (canned vegetables, DOE)319 kJ/kg
- TypicalCurrent typical on-site energy of retort sterilisation (canned vegetables, DOE)505 kJ/kg
- Required lethality at the cold spot (12-D botulinum cook or legal F0, whichever is larger)3.00 min
- Thermal diffusivity of the product at the mean process temperature0.176 [0.131–0.175] mm²/s
- Heating rate index f_h of the cold spot (first-term asymptote)27.8 [28.0–37.3] min
- Heating lag factor j of the geometric centre (first-term asymptote)2.04
- TheoreticalMinimum heating time at retort temperature for the required lethality40.5 [38.5–52.5] min
- Heating time with the capability margin on lethality47.5 [45.8–69.8] min
- Heating time for the commercial target F0 of the documented product (model check)53.0 [51.0–66.8] min
- Best documentedDocumented process time at 121.1 °C for the commercial target50.0 min
- Minimum cooling time until the centre reaches the unloading temperature27.8 [26.3–46.0] min
- Minimum retort cycle (venting, heating, cooling, loading and unloading)92.3 [87.6–124.8] min
- Cooling time after the capable (design) heating time28.0 [26.5–46.5] min
- Retort cycle of the capable process (design heating time, cooling, venting, loading and unloading)99.5 [96.6–139.6] min
- TheoreticalMaximum cans per hour per cubic metre of retort (densest packing, heating and cooling only)3,094 [2,217–3,175] 1/h/m³
- Standard deviation of ln F0 across the load0.250 [0.187–0.513]
- Design lethality over required lethality at the nominal cold spot2.12 [1.72–5.06]
- Share of containers below the required lethality0.00135 [0.00025–0.00578]
- TheoreticalMaximum yield (hermetic container: no mass leaves)1.00
- TheoreticalMaximum OEE quality factor0.9987 [0.9942–0.9997]
- TheoreticalMaximum availability (periodic cleaning; batch transfer steps belong to the ideal cycle)0.958 [0.918–0.978]
- TheoreticalMaximum performance factor: ideal batch cycle over the cycle of the capable process (lethality margin)0.927 [0.833–0.953]
- TheoreticalPhysics-bounded OEE0.887 [0.781–0.915]
3Ceilings per dimension
- Theoretical
- Best available technique
- Best documented
- Typical
- TheoreticalThermodynamic minimum heat (product returns to ambient)0 kJ/kg
- TheoreticalDOE bandwidth study, thermodynamic minimum energy intensity of canned fruits and vegetables · Benchmark0 kJ/kg
- Best available techniqueDOE bandwidth study, state of the art of retort sterilisation, canned fruits and vegetables · Benchmark319 kJ/kg
- Best available techniqueState-of-the-art on-site energy of retort sterilisation (canned vegetables, DOE)319 kJ/kg
- TypicalDOE bandwidth study, current typical retort sterilisation, canned fruits and vegetables · Benchmark505 kJ/kg
- TypicalCurrent typical on-site energy of retort sterilisation (canned vegetables, DOE)505 kJ/kg
- TheoreticalMinimum heating time at retort temperature for the required lethality40.5 [38.5–52.5] min
- Best documentedDocumented process time at 121.1 °C for the commercial target50.0 min
- Best documentedDocumented process for solid-pack tuna in 84 × 46.5 mm cans: 50 min at 121.1 °C for F0 = 10 min (timed from the moment the retort reaches temperature) · Benchmark50.0 min
- TheoreticalMaximum cans per hour per cubic metre of retort (densest packing, heating and cooling only)3,094 [2,217–3,175] 1/h/m³
- TheoreticalMaximum yield (hermetic container: no mass leaves)1.00
- TheoreticalMaximum OEE quality factor0.9987 [0.9942–0.9997]
- TheoreticalMaximum availability (periodic cleaning; batch transfer steps belong to the ideal cycle)0.958 [0.918–0.978]
- TheoreticalMaximum performance factor: ideal batch cycle over the cycle of the capable process (lethality margin)0.927 [0.833–0.953]
- TheoreticalPhysics-bounded OEE0.887 [0.781–0.915]
4Loss cascade
- TheoreticalBest available techniqueEnergy per unit of product0 kJ/kg → 319 kJ/kg (gap 319 kJ/kg)
The thermodynamic minimum is zero because the product leaves at roughly the temperature it entered: every joule used to heat it could in principle be recovered while cooling it, exactly as in regenerative pasteurisation. A batch retort cannot regenerate between the hot load and the next cold load without storage, so it supplies at least the sensible heat of product and can, plus the heat of the retort shell, the water used for venting and the condensate; the state-of-the-art value already assumes heat recovery and efficient venting.
- Best available techniqueTypicalEnergy per unit of product319 kJ/kg → 505 kJ/kg (gap 186 kJ/kg)
Typical retorts vent with live steam to atmosphere, heat the vessel and the water of water-immersion systems at every cycle, lose heat through uninsulated shells and discard the cooling water without recovering its heat.
- TheoreticalBest documentedCycle or residence time40.5 [38.5–52.5] min → 50.0 min (gap 9.50 min)
The theoretical heating time delivers exactly the required botulinum lethality (F0 = 3 min) at the centre of a nominal can whose wall is stepped instantly to retort temperature. The documented process targets F0 = 10 min to control heat-resistant spoilage spores beyond the safety minimum, adds a margin for can-to-can variation of fill, initial temperature and retort temperature distribution, and is timed after a come-up period; conduction into the solid pack (heating rate index of tens of minutes) dominates all of them.
- TheoreticalTypicalPerformance
Under the common batch convention these steps belong to the ideal cycle and act through performance. A batch retort spends part of every cycle closed but not processing (venting, come-up) or open (loading, unloading); continuous rotary or hydrostatic sterilisers remove most of the handling time but keep the venting and come-up physics.
5Physics-bounded OEE
- Loading time (ideal)1.000
- Availabilityfactor 0.958 [0.918–0.978]0.958 (−0.042)
- Performancefactor 0.927 [0.833–0.953]0.889 (−0.070)
- Qualityfactor 0.9987 [0.9942–0.9997]0.887 (−0.001)
- Physics-bounded OEE0.887 [0.781–0.915]
6Full derivation
Scope. Solid-pack fish (tuna style) in 84 × 46.5 mm cans, sterilised in a batch retort with saturated steam at 121.1 °C and cooled with water. The pack heats by conduction, so the slowest-heating point of each can is its geometric centre. Symbols, values, units, uncertainty distributions and sources are listed in the parameter table generated from config/physics/sterilization.yaml.
1. Mass balance — maximum yield
The container is hermetically sealed before heating: no product can leave it, and no water evaporates from the food. The mass balance of the operation is therefore and the physical yield ceiling is exactly . Cans that leak, seams that fail inspection, dented or buckled cans and cans that peak because they were cooled without overpressure are losses of the installed technology (seaming, handling, pressure control), not of physics; they belong to the gap between this ceiling and the documented operation.
2. Energy balance — minimum energy per unit of product
The product enters the retort at , is heated to the retort temperature and leaves at roughly the temperature at which it entered. Its net enthalpy change is close to zero.
Thermodynamic minimum. As in regenerative pasteurisation, all the heat given to the product while heating could in principle be taken back from it while cooling and given to the next load: the reversible minimum is zero. This agrees with the thermodynamic minimum of 0 that the US DOE bandwidth study assigns to canned fruits and vegetables, which involve no significant chemical change.
Minimum without heat recovery. A batch retort does not regenerate between a hot load and the next cold load. If no heat is recovered, the heat supplied per kilogram of product is at least the sensible heat of the product and its container:
where is the specific heat of the product, the mass of container per unit mass of product and the specific heat of the tinplate. The heat of the retort shell, the steam blown off during venting, the water of water-immersion retorts and the losses through the shell come on top.
The energy ceilings. Theoretical: 0. Best available technique: the DOE state-of-the-art on-site energy intensity of retort sterilisation of canned fruits and vegetables (137 Btu/lb), which is of the same size as and so already implies efficient venting and some heat recovery. Typical: the DOE current typical value (217 Btu/lb). The DOE practical minimum (92 Btu/lb, technologies under development) and the electricity plus heat of complete fish canning lines in the BAT reference document (150–190 kWh per tonne of fish, which include precooking and auxiliaries) are listed as benchmarks.
UHT variant. In continuous ultra-high-temperature treatment of pumpable products followed by aseptic filling, the product flows through heat exchangers and can be regenerated like a pasteuriser; the energy balance then approaches the zero minimum asymptotically as the regeneration effectiveness tends to one, and the rate limit becomes the holding time at a high temperature rather than conduction into a container. The same kinetics (section 3) apply.
3. Rate-limiting step — minimum process time and maximum throughput
Kinetics. Bacterial spores die by a first-order process at constant temperature, , so with the decimal reduction time : the time that kills 90 % of the population. Over the range of sterilisation temperatures falls tenfold for every kelvin of temperature rise,
One minute at temperature therefore has the same effect as minutes at the reference temperature = 121.1 °C; is the lethal rate. With = 10 °C, one minute at 111.1 °C is worth 0.1 min at 121.1 °C and one minute at 101.1 °C only 0.01 min. The lethality delivered at a point is
Required lethality. The minimum safety requirement for low-acid canned food is the destruction of Clostridium botulinum spores; the accepted process reduces their number by twelve decades (the "12-D" or botulinum cook): min. An EU legal text states the treatment of meat products in hermetically sealed containers as "a Fo value of three or more". The model uses = 3 min at the cold spot.
Heat penetration. The pack is a finite cylinder of radius and half-height with thermal diffusivity , where is the thermal conductivity, the density and the specific heat of the product. If the can wall is brought to the retort temperature at , the exact solution of the heat equation at the geometric centre is the product of the solutions for an infinite cylinder and an infinite slab:
where are the roots of the Bessel function , is the Bessel function of order one and . Thirty terms of each series are summed. Cooling is added by superposition: when steam is shut off at time and cooling water at floods the retort, the wall temperature steps down by , and the centre temperature becomes the heating response minus times the same step response delayed by . Because heat keeps flowing inwards for a while after the wall is cooled, the centre temperature continues to rise briefly and part of the lethality is delivered during cooling; the model includes it.
For long times only the first term of each series survives and the centre approaches the classical semi-logarithmic heating line of Ball's method,
where is the heating rate index (the time for the temperature difference to fall tenfold) and the lag factor of the geometric centre. They are reported as outputs; the lethality itself is computed with the full series.
Product properties. The FAO gives the thermal conductivity of unfrozen white fish at 0 °C (0.37 to 0.5 kcal m⁻¹ h⁻¹ K⁻¹), its density (1 054 kg/m³) and specific heat (0.9 kcal kg⁻¹ K⁻¹). Fish is mostly water, and the conductivity of liquid water rises by about a fifth between 0 °C and the mean process temperature; the conductivity is therefore scaled by from IAPWS through CoolProp, with .
Minimum heating time. is the smallest heating time (on a grid of 0.25 min) for which at the centre of a nominal can. It is a lower bound because the wall is assumed to reach the retort temperature instantly (no come-up ramp, no resistance of the condensing steam film). The output heat_time_commercial repeats the calculation for the commercial target of the documented product, = 10 min; it agrees with the FAO process of 50 min at 121.1 °C for solid-pack tuna in 84 × 46.5 mm cans to within a few minutes, the documented time being counted after a come-up period that already heats the cans.
Cooling time. is the time from steam-off until the centre, past its peak, falls to the unloading temperature .
Maximum throughput. Equal parallel cylinders fill at most a fraction of space (hexagonal packing). A retort volume holds cans, with , and each load occupies it for , so
4. Process capability — quality ceiling
The lethality at the cold spot differs from can to can: the diffusivity varies with fill and composition (relative standard deviation ), the initial temperature varies () and the heating medium is not perfectly uniform across the load (). Since depends exponentially on temperature, is close to normally distributed. Its standard deviation is obtained by perturbing each source by one standard deviation at the minimum heating time:
The processor targets at the nominal can, so that the share of under-processed containers is
The over-processing factor is the price in heating time and in product quality (texture, colour, nutrients) of that safety margin; the heating time that delivers it is heat_time_design.
5. Unavoidable stops — maximum availability
A batch retort is closed and pressurised while it processes. Between loads the baskets must be moved out and in (), and before the processing time may start, the air must be vented: air left in a steam retort forms cold pockets. The US regulation prescribes venting schedules; the shortest is a valve "wide open for at least 4 minutes and to at least 220 °F", other arrangements need 5 to 8 minutes. Under the common batch convention of all models, venting and loading/unloading are not availability losses: like heating and cooling, they are steps every batch needs, so they belong to the ideal batch cycle at their regulatory or declared minimum,
and act through the performance factor (section 6). Availability counts only the periodic cleaning of the retort room equipment, of declared duration every (retorts and their cooling-water circuits are not cleaned in place as a closed product circuit, so the cleaning model does not apply):
The come-up time beyond venting is not counted (the wall is stepped instantly), which makes the bound optimistic.
6. Physics-bounded OEE
Scope of the bound. The theoretical label of means physics-bounded under the declared scenario: the ceiling follows from the physics of the operation for the declared product, equipment and schedule, and it is a bound only conditional on those declarations. It follows the common definition of all models: counts only stops required by regulation or forced by a physical mechanism, at their physical minimum duration, plus the start-up they force; is the ratio of the physics-limited ideal cycle to the cycle of the capable process; is the share of conforming units, and mass losses of conforming product are reported only as yield.
The reference is the ideal batch cycle of section 5, which delivers exactly the required lethality. The under-processed share of section 4, , holds only for loads heated for the design time ( is the cooling time after it), so is the price in time of making every container safe, as the capable seal dwell in the packaging model: 92.25/99.5 = 0.927 at the point values, and = 0.887. The Monte Carlo intervals over the declared uncertainty of every input are reported in the output table.
7. Assumptions and validity
See the assumption and validity lists generated from the configuration file. The thermal properties of the product (conductivity, density, specific heat) are FAO values for white fish and can later be replaced by a composition-based property model. The most influential inputs (sensitivity table) are the conductivity and the initial temperature for the heating time, and the loading and venting times for the performance factor.
References
- Food and Agriculture Organization of the United Nations. Planning and engineering data 2. Fish canning, FAO Fisheries Circular No. 784, 1988 (chapters 1 and 4).
- Food and Agriculture Organization of the United Nations. Freezing and refrigerated storage in fisheries, FAO Fisheries Technical Paper 340, 1994 (chapter 19, properties of fish).
- U.S. Code of Federal Regulations, Title 21, Part 113, Thermally Processed Low-Acid Foods Packaged in Hermetically Sealed Containers, 2025 edition.
- Commission Delegated Regulation (EU) 2020/692, Annex XXVI.
- European Commission, Joint Research Centre. Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries, 2019.
- U.S. Department of Energy. Bandwidth Study on Energy Use and Potential Energy Saving Opportunities in U.S. Food and Beverage Manufacturing, 2017.
- Bell, I. H., Wronski, J., Quoilin, S., Lemort, V. (2014). Pure and pseudo-pure fluid thermophysical property evaluation and the open-source thermophysical property library CoolProp. Industrial & Engineering Chemistry Research, 53, 2498–2508. doi:10.1021/ie4033999
7Parameters and provenance
- 0.23 min
Decimal reduction time of Clostridium botulinum spores at 121.1 °C (upper value)
Property · Fixed
Verified quoteShow verbatim quote
(12 D= 12 x 0.23 = 2.8 min)Planning and engineering data 2. Fish canning (FAO Fisheries Circular No. 784), chapter 1: Canning principles (opens in a new tab). Food and Agriculture Organization of the United Nations, 1988. FAO Fisheries Circular No. 784, FIIU/C784(En)
- 12
Number of decimal reductions of C. botulinum accepted as safe (12-D botulinum cook)
Regulatory · Fixed
Verified quoteShow verbatim quote
(12 D= 12 x 0.23 = 2.8 min)Planning and engineering data 2. Fish canning (FAO Fisheries Circular No. 784), chapter 1: Canning principles (opens in a new tab). Food and Agriculture Organization of the United Nations, 1988. FAO Fisheries Circular No. 784, FIIU/C784(En)
- 3 min
Legal minimum lethality of a treatment in a hermetically sealed container
Regulatory · Fixed
Verified quoteShow verbatim quote
B = Treatment in a hermetically sealed container to a Fo value of three or more.Commission Delegated Regulation (EU) 2020/692 of 30 January 2020 (rules for entry into the Union of consignments of certain animals, germinal products and products of animal origin) (opens in a new tab). Publications Office of the European Union, 2020. p. 138. CELEX 32020R0692; OJ L 174, 3.6.2020, p. 379
- 10 K
Temperature change that alters the decimal reduction time tenfold
Property · Fixed
Verified quoteShow verbatim quote
the lethal rates at 91.1, 101.1, 111.1, 131.1, 141.1 and 151.1 �C are 0.001, 0.01, 0.1, 10, 100 and 1 000, respectivelyPlanning and engineering data 2. Fish canning (FAO Fisheries Circular No. 784), chapter 1: Canning principles (opens in a new tab). Food and Agriculture Organization of the United Nations, 1988. FAO Fisheries Circular No. 784, FIIU/C784(En)
- 121.1 °C
Reference temperature of F0
Regulatory · Fixed
Verified quoteShow verbatim quote
an F o value of one minute is equivalent to holding the product at 121.1Planning and engineering data 2. Fish canning (FAO Fisheries Circular No. 784), chapter 1: Canning principles (opens in a new tab). Food and Agriculture Organization of the United Nations, 1988. FAO Fisheries Circular No. 784, FIIU/C784(En)
- 10 min
Commercial target lethality of the documented canned tuna process
Technology · Fixed
Verified quoteShow verbatim quote
a process for solid style canned tuna packed in 84 x 46.5 mm cans may have a target Fo value of 10 minPlanning and engineering data 2. Fish canning (FAO Fisheries Circular No. 784), chapter 1: Canning principles (opens in a new tab). Food and Agriculture Organization of the United Nations, 1988. FAO Fisheries Circular No. 784, FIIU/C784(En)
- 50 min
Documented process time at 121.1 °C for the commercial target
Benchmark · Fixed
Verified quoteShow verbatim quote
which can be achieved by processing for 74 min at 116 �C or 50 min at 121.1Planning and engineering data 2. Fish canning (FAO Fisheries Circular No. 784), chapter 1: Canning principles (opens in a new tab). Food and Agriculture Organization of the United Nations, 1988. FAO Fisheries Circular No. 784, FIIU/C784(En)
- 121.1 °C
Retort (heating medium) temperature
Technology · Fixed
Verified quoteShow verbatim quote
which can be achieved by processing for 74 min at 116 �C or 50 min at 121.1Planning and engineering data 2. Fish canning (FAO Fisheries Circular No. 784), chapter 1: Canning principles (opens in a new tab). Food and Agriculture Organization of the United Nations, 1988. FAO Fisheries Circular No. 784, FIIU/C784(En)
- 0.084 m
Can diameter
Scenario · Fixed
Verified quoteShow verbatim quote
packed in 84 x 46.5 mm cansPlanning and engineering data 2. Fish canning (FAO Fisheries Circular No. 784), chapter 1: Canning principles (opens in a new tab). Food and Agriculture Organization of the United Nations, 1988. FAO Fisheries Circular No. 784, FIIU/C784(En)
- 0.0465 m
Can height
Scenario · Fixed
Verified quoteShow verbatim quote
packed in 84 x 46.5 mm cansPlanning and engineering data 2. Fish canning (FAO Fisheries Circular No. 784), chapter 1: Canning principles (opens in a new tab). Food and Agriculture Organization of the United Nations, 1988. FAO Fisheries Circular No. 784, FIIU/C784(En)
- 40 °C
Initial product temperature at the start of heating
Scenario · Uniform 25 to 60 °C
Declared assumptionPrecooked and cooled loins filled with oil recommended at 80 °C–90 °C (fao_fc784_ch4_processing); the mixture temperature at retort start is a declared assumption.
- 0.5 kcal/h/m/K
Thermal conductivity of unfrozen fish at 0 °C
Property · Uniform 0.37 to 0.5 kcal/h/m/K
Verified quoteShow verbatim quote
Unfrozen white fish at 0�C0.37 to 0.5Freezing and refrigerated storage in fisheries (FAO Fisheries Technical Paper 340), chapter 19: Some related facts and figures (opens in a new tab). Food and Agriculture Organization of the United Nations, 1994. FAO Fisheries Technical Paper 340; ISBN 92-5-103579-2
- 1,054 kg/m³
Density of the product
Property · Fixed
Verified quoteShow verbatim quote
Density of white fish muscle (kg/m3) at 0�C1 054Freezing and refrigerated storage in fisheries (FAO Fisheries Technical Paper 340), chapter 19: Some related facts and figures (opens in a new tab). Food and Agriculture Organization of the United Nations, 1994. FAO Fisheries Technical Paper 340; ISBN 92-5-103579-2
- 0.9 kcal/kg/K
Specific heat of the unfrozen product
Property · Fixed
Verified quoteShow verbatim quote
Specific heat of white fish (kcal/kg deg C) Unfrozen 0.9 Frozen 0.4Freezing and refrigerated storage in fisheries (FAO Fisheries Technical Paper 340), chapter 19: Some related facts and figures (opens in a new tab). Food and Agriculture Organization of the United Nations, 1994. FAO Fisheries Technical Paper 340; ISBN 92-5-103579-2
- 0.2
Mass of the can per unit mass of product
Scenario · Uniform 0.15 to 0.25
Declared assumptionDeclared assumption for a small tinplate can; replace with the weighed can and fill.
- 0.48 kJ/kg/K
Specific heat of the tinplate container
Property · Uniform 0.45 to 0.5 kJ/kg/K
Declared assumptionDeclared assumption for carbon steel; no open source was registered for it.
- 20 °C
Cooling-water temperature
Scenario · Uniform 15 to 30 °C
Declared assumption - 40 °C
Centre temperature at which cans are unloaded
Scenario · Uniform 35 to 45 °C
Declared assumptionDeclared assumption: cans are unloaded warm enough to dry the seams.
- 0.05
Can-to-can relative standard deviation of the thermal diffusivity (fill, composition)
Scenario · Uniform 0.03 to 0.1
Declared assumptionCapability assumption; replace with the spread of the plant's heat-penetration tests.
- 0.5 K
Standard deviation of the heating-medium temperature across the load
Scenario · Uniform 0.25 to 1 K
Declared assumptionCapability assumption; replace with the temperature-distribution test of the retort.
- 2 K
Standard deviation of the initial product temperature
Scenario · Uniform 1 to 5 K
Declared assumption - 3
Design margin on ln F0, in standard deviations
Scenario · Uniform 2.5 to 3.5
Declared assumptionOperating choice of the processor, point value at the centre of the declared range 2.5-3.5; it sets the under-processed share and the over-processing factor.
- 4 min
Minimum venting time of a steam retort
Regulatory · Uniform 4 to 8 min
Verified quoteShow verbatim quote
Vent gate or plug cock valve should be wide open for at least 4 minutes and to at least 22021 CFR Part 113 — Thermally Processed Low-Acid Foods Packaged in Hermetically Sealed Containers (4-1-25 Edition) (opens in a new tab). U.S. Government Publishing Office (Code of Federal Regulations, Title 21, Chapter I), 2025. p. 8. 21 CFR 113 (2025)
- 20 min
Loading and unloading time of the retort baskets per cycle
Scenario · Uniform 10 to 30 min
Declared assumptionDeclared assumption; replace with the measured handling time.
- 24 h
Operating time between two cleanings of the retort room equipment
Scenario · Fixed
Declared assumption - 1 h
Duration of the cleaning
Scenario · Uniform 0.5 to 2 h
Declared assumption - 137 Btu/lb
State-of-the-art on-site energy intensity of heat sterilisation (retorting), canned fruits and vegetables
Benchmark · Fixed
Verified quoteShow verbatim quote
Heat sterilization (retorting) 217 137 92 0Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (opens in a new tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. p. 39. DOE/EE-1571; OSTI ID 1512366
- 217 Btu/lb
Current typical on-site energy intensity of heat sterilisation (retorting), canned fruits and vegetables
Benchmark · Fixed
Verified quoteShow verbatim quote
Heat sterilization (retorting) 217 137 92 0Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (opens in a new tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. p. 39. DOE/EE-1571; OSTI ID 1512366
8Benchmarks
| Benchmark | Ceiling | Value | Provenance |
|---|---|---|---|
DOE bandwidth study, thermodynamic minimum energy intensity of canned fruits and vegetablesShow verbatim quoteCanned Fruits and Vegetables 0 17,658 0Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (opens in a new tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. p. 26. DOE/EE-1571; OSTI ID 1512366 | Theoretical | 0 Btu/lb | Verified quote |
DOE bandwidth study, practical minimum (R&D technologies) of retort sterilisation, canned fruits and vegetablesShow verbatim quoteHeat sterilization (retorting) 217 137 92 0Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (opens in a new tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. p. 39. DOE/EE-1571; OSTI ID 1512366 | — | 92 Btu/lb | Verified quote |
DOE bandwidth study, state of the art of retort sterilisation, canned fruits and vegetablesShow verbatim quoteHeat sterilization (retorting) 217 137 92 0Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (opens in a new tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. p. 39. DOE/EE-1571; OSTI ID 1512366 | Best available technique | 137 Btu/lb | Verified quote |
DOE bandwidth study, current typical retort sterilisation, canned fruits and vegetablesShow verbatim quoteHeat sterilization (retorting) 217 137 92 0Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (opens in a new tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. p. 39. DOE/EE-1571; OSTI ID 1512366 | Typical | 217 Btu/lb | Verified quote |
Energy use of fish canning, whole canning line (lower end); includes precooking, filling and auxiliaries, so it bounds the retort from aboveShow verbatim quotecanning consumes 150–190 kWh/t of fishBest Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (opens in a new tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. p. 416. EUR 29978 EN; JRC118627; doi:10.2760/243911 | Best documented | 150 kW·h/tonne | Verified quote |
Energy use of fish canning, whole canning line (upper end)Show verbatim quotecanning consumes 150–190 kWh/t of fishBest Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (opens in a new tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. p. 416. EUR 29978 EN; JRC118627; doi:10.2760/243911 | Typical | 190 kW·h/tonne | Verified quote |
Documented process for solid-pack tuna in 84 × 46.5 mm cans: 50 min at 121.1 °C for F0 = 10 min (timed from the moment the retort reaches temperature)Show verbatim quotewhich can be achieved by processing for 74 min at 116 �C or 50 min at 121.1Planning and engineering data 2. Fish canning (FAO Fisheries Circular No. 784), chapter 1: Canning principles (opens in a new tab). Food and Agriculture Organization of the United Nations, 1988. FAO Fisheries Circular No. 784, FIIU/C784(En) | Best documented | 50 min | Verified quote |
Second heat treatment of sterilised milk in containers: autoclave or continuous retort at about 110–125 °C for 20 to 40 minutes (convection-heating liquid, upper end)Show verbatim quotein an autoclave in batches or in a continuous retort at approximately 110–125 °C for 20 to 40 minutesBest Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (opens in a new tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. p. 338. EUR 29978 EN; JRC118627; doi:10.2760/243911 | Typical | 40 min | Verified quote |
9Unavoidable stops
- Venting of the steam retort (regulatory minimum; part of the ideal batch cycle, acts through performance)Verified quote
Air left in a steam retort forms cold pockets; the regulation prescribes minimum venting times and temperatures before the processing time may start.
Show verbatim quote
Vent gate or plug cock valve should be wide open for at least 4 minutes and to at least 22021 CFR Part 113 — Thermally Processed Low-Acid Foods Packaged in Hermetically Sealed Containers (4-1-25 Edition) (opens in a new tab). U.S. Government Publishing Office (Code of Federal Regulations, Title 21, Chapter I), 2025. 21 CFR 113 (2025)
- Loading and unloading of baskets (part of the ideal batch cycle, acts through performance)Declared assumption
A batch retort is closed while it processes; baskets must be moved in and out between cycles.
- CleaningDeclared assumption
Retort room equipment and cooling water circuits are cleaned periodically; interval and duration are declared assumptions.
10Assumptions
- Common batch convention: venting (regulatory minimum), loading and unloading (declared), heating and cooling belong to the ideal batch cycle and act through the performance factor, the ratio of the ideal cycle at the minimum heating time to the cycle of the capable process (design heating time). Availability counts only the periodic cleaning of the retort room equipment, at a declared duration: retorts and their cooling-water circuits are not cleaned in place as a closed product circuit, so the cleaning model does not apply.
- First-order inactivation with D and z constant over 100–125 °C; lethality is integrated at the geometric centre, which is the slowest-heating point of a conduction-heating can.
- Pure conduction with constant properties in a finite cylinder of the can's outer dimensions; the wall follows the medium temperature instantly (no come-up ramp, no surface resistance of condensing steam or water), so the computed heating time is a lower bound.
- Product conductivity is the FAO value for unfrozen white fish at 0 °C scaled by the ratio of the conductivity of liquid water at the mean process temperature to that at 0 °C; density and specific heat are the FAO values for white fish.
- Can-to-can variation of ln F0 combines independent variations of diffusivity, retort temperature and initial temperature; the processor targets the required lethality plus z standard deviations.
- Seam defects, leakers and damaged cans are technology losses, not physics: the yield ceiling of a hermetic container is 1.
11Range of validity
- Low-acid foods (pH above 4.6) in rigid cans that heat by conduction (solid packs of fish or meat, purées); convection-heating packs heat several times faster and need a heat-penetration model with mixing.
- Retort temperatures between about 110 °C and 125 °C.
12Sensitivity
- Reference temperature of F0elasticity -0.242Spearman ρ —
- Retort (heating medium) temperatureelasticity +0.223Spearman ρ —
- Can-to-can relative standard deviation of the thermal diffusivity (fill, composition)elasticity -0.076Spearman ρ -0.80
- Design margin on ln F0, in standard deviationselasticity -0.062Spearman ρ -0.24
- Operating time between two cleanings of the retort room equipmentelasticity +0.044Spearman ρ —
- Duration of the cleaningelasticity -0.043Spearman ρ -0.47
- Cooling-water temperatureelasticity +0.033Spearman ρ +0.07
- Density of the productelasticity -0.031Spearman ρ —
- Specific heat of the unfrozen productelasticity -0.031Spearman ρ —
- Thermal conductivity of unfrozen fish at 0 °Celasticity +0.029Spearman ρ +0.01
- Standard deviation of the heating-medium temperature across the loadelasticity -0.025Spearman ρ -0.15
- Initial product temperature at the start of heatingelasticity +0.021Spearman ρ +0.08
- Centre temperature at which cans are unloadedelasticity -0.019Spearman ρ -0.05
- Loading and unloading time of the retort baskets per cycleelasticity +0.016Spearman ρ +0.13
- Temperature change that alters the decimal reduction time tenfoldelasticity +0.014Spearman ρ —
- Can diameterelasticity -0.012Spearman ρ —
- Legal minimum lethality of a treatment in a hermetically sealed containerelasticity +0.006Spearman ρ —
- Minimum venting time of a steam retortelasticity +0.003Spearman ρ +0.03
- Can heightelasticity -0.001Spearman ρ —
- Standard deviation of the initial product temperatureelasticity 0.000Spearman ρ -0.05
- Output rises with the parameter
- Output falls with the parameter
13Validation checks
- Dimensional analysis25 outputs converted to their declared unitsPassed
- Every cited value verified against its source25 verified, 0 failedPassed
- No documented value beats the theoretical limitPassed
- Ceilings in physical orderPassed
- Fractions within 0 and 1Passed
14Causes of loss in this operation
- Sterilizer piping and valve component failureEquipment failure (breakdowns)6.2% [1.9–13.9%]B34 studies
- Autoclave door/seal mechanism malfunctionEquipment failure (breakdowns)1.7% [0.3–4.9%]C34 studies
- Pressure sensor/transmitter calibration drift (autoclave)Equipment failure (breakdowns)1.1% [0.2–3.2%]D34 studies
- Sterilizer conveyor chain derailmentEquipment failure (breakdowns)1.1% [0.2–3.3%]D34 studies
- Control instrument misalignmentEquipment failure (breakdowns)1.1% [0.2–3.3%]D34 studies
- Autoclave filter clogging causing overheatingEquipment failure (breakdowns)1.1% [0.2–3.1%]D34 studies
- Structural failure of support railEquipment failure (breakdowns)1.1% [0.2–3.2%]D34 studies
- Minor stoppages on sterilizerIdling and minor stops (micro-stops)0.9% [0.1–2.9%]D34 studies
- Container guide rail tilting/misalignment failureEquipment failure (breakdowns)0.6% [0.1–2.1%]D34 studies
15References
- Planning and engineering data 2. Fish canning (FAO Fisheries Circular No. 784), chapter 1: Canning principles (opens in a new tab). Food and Agriculture Organization of the United Nations, 1988. FAO Fisheries Circular No. 784, FIIU/C784(En)
- fao_fc784_ch4_processing
- Freezing and refrigerated storage in fisheries (FAO Fisheries Technical Paper 340), chapter 19: Some related facts and figures (opens in a new tab). Food and Agriculture Organization of the United Nations, 1994. FAO Fisheries Technical Paper 340; ISBN 92-5-103579-2
- 21 CFR Part 113 — Thermally Processed Low-Acid Foods Packaged in Hermetically Sealed Containers (4-1-25 Edition) (opens in a new tab). U.S. Government Publishing Office (Code of Federal Regulations, Title 21, Chapter I), 2025. p. 8. 21 CFR 113 (2025)
- Commission Delegated Regulation (EU) 2020/692 of 30 January 2020 (rules for entry into the Union of consignments of certain animals, germinal products and products of animal origin) (opens in a new tab). Publications Office of the European Union, 2020. p. 138. CELEX 32020R0692; OJ L 174, 3.6.2020, p. 379
- Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (opens in a new tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. p. 416. EUR 29978 EN; JRC118627; doi:10.2760/243911
- Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (opens in a new tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. p. 39. DOE/EE-1571; OSTI ID 1512366
- doi:10.1021/ie4033999 — Thermophysical property library (water conductivity).

