foratvise
Get Started
Equipment failure (breakdowns)

Metal conveyor chain/track failure

Equipment failure (breakdowns)AvailabilityConveying and accumulation

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 1 of the 86 studies that could observe it (sparse evidence).

What happens

Wear, elongation, misalignment or breakage of the metal chain, links or track that drives the conveyor section causes the mechanism to bind, derail or stop moving, interrupting the flow of product along the line. Because the damaged component cannot be cleared by a simple operator reset, a mechanical intervention is needed to realign, repair or replace the affected part.

What is done about it

Implement a preventive maintenance routine that inspects chain tension, lubrication, wear on links and sprockets, and track alignment, replacing worn components before they reach failure. Install condition-monitoring sensors (current, vibration, tension) to trigger early warnings and schedule replacement during planned downtime.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.7% [0.1–1.8%]
Expected share of lost time
0.4% [0.1–1.0%]
Share of lost time when present
57% [46–67%]
Studies / units
86 / 112
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.8% [0.1–2.8%]11 studies
  • Soft drinks, bottled water and juices
    0.9% [0.1–2.9%]28 studies
  • Brewing, wine and spirits
    0.7% [0.1–2.5%]12 studies
  • Bakery and pasta
    0.8% [0.1–3.0%]0 studies
  • Meat, poultry and seafood
    0.8% [0.1–2.9%]5 studies
  • Fruit and vegetable processing
    0.8% [0.1–3.0%]4 studies
  • Grain and oilseed milling
    0.8% [0.1–2.9%]4 studies
  • Sugar and confectionery
    0.8% [0.1–3.1%]4 studies
  • Snacks, coffee, tea and other foods
    0.8% [0.1–2.8%]4 studies
  • Animal feed and pet food
    0.8% [0.1–3.1%]5 studies
  • Food manufacturing (unspecified or mixed)
    0.8% [0.1–2.8%]9 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Wear, elongation, misalignment or breakage of the metal chain, links or track that drives the conveyor section causes the mechanism to bind, derail or stop moving, interrupting the flow of product along the line. Because the damaged component cannot be cleared by a simple operator reset, a mechanical intervention is needed to realign, repair or replace the affected part.

How it looks in SCADA data

Engineering guidance

Shows up as an unplanned stop state on the conveyor drive with motor current or torque spikes followed by a drive fault or overload trip, and no product-jam sensor flag. Upstream and downstream equipment register starvation or blocking states while the conveyor remains stopped, and the event duration is consistent with a maintenance-logged repair rather than an operator-cleared minor stop.

Countermeasure

Engineering guidance

Implement a preventive maintenance routine that inspects chain tension, lubrication, wear on links and sprockets, and track alignment, replacing worn components before they reach failure. Install condition-monitoring sensors (current, vibration, tension) to trigger early warnings and schedule replacement during planned downtime.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of loss events: 66.0 % · as reported: “Desgaste das correntes”
    Show verbatim quote
    Desgaste das correntes gerando quebras nas esteiras de acordo com os dados históricos representava 66 % das ocorrências, sendo assim validada como causa-raiz.
  2. Lost time: 3.00 h · as reported: “Metal jalan”
    Show verbatim quote
    Metal jalan | Suara kasar, asap hitam akibat keausan | Teknisi eksternal | Rp187.000 | 3 Jam 0 Menit