foratvise
Get Started
Setup and adjustments

Conveyor cleaning during changeover

Setup and adjustmentsAvailabilityConveying and accumulation

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 1 of the 86 studies that could observe it (sparse evidence).

What happens

As part of a product or format changeover, conveyors and accumulation tables must be stopped, emptied and cleaned (removing spilled product, residue or debris) before the next run can start, taking the line out of production. This cleaning step is planned work tied to the changeover rather than a failure, but it consumes time between the last good unit of one run and the first good unit of the next.

What is done about it

Standardize and simplify conveyor cleaning procedures (quick-release guards, accessible wash points, dedicated cleaning tools) and integrate them into a structured changeover sequence (SMED) so cleaning tasks run in parallel with other setup activities rather than sequentially.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.6% [0.1–1.7%]
Expected share of lost time
0.3% [0.1–1.0%]
Share of lost time when present
57% [45–67%]
Studies / units
86 / 112
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.7% [0.1–2.5%]11 studies
  • Soft drinks, bottled water and juices
    0.6% [0.1–2.1%]28 studies
  • Brewing, wine and spirits
    0.7% [0.1–2.4%]12 studies
  • Bakery and pasta
    0.7% [0.1–2.7%]0 studies
  • Meat, poultry and seafood
    0.7% [0.1–2.5%]5 studies
  • Fruit and vegetable processing
    0.7% [0.1–2.9%]4 studies
  • Grain and oilseed milling
    0.7% [0.1–2.7%]4 studies
  • Sugar and confectionery
    0.7% [0.1–2.9%]4 studies
  • Snacks, coffee, tea and other foods
    1.0% [0.1–3.7%]4 studies
  • Animal feed and pet food
    0.7% [0.1–2.8%]5 studies
  • Food manufacturing (unspecified or mixed)
    0.7% [0.1–2.5%]9 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

As part of a product or format changeover, conveyors and accumulation tables must be stopped, emptied and cleaned (removing spilled product, residue or debris) before the next run can start, taking the line out of production. This cleaning step is planned work tied to the changeover rather than a failure, but it consumes time between the last good unit of one run and the first good unit of the next.

How it looks in SCADA data

Engineering guidance

SCADA/MES shows the conveyor or line in a changeover/cleaning state with motors stopped and zero product counts for an extended, recurring interval that coincides with scheduled changeover events; upstream and downstream equipment show matching idle or standby states rather than fault alarms.

Countermeasure

Engineering guidance

Standardize and simplify conveyor cleaning procedures (quick-release guards, accessible wash points, dedicated cleaning tools) and integrate them into a structured changeover sequence (SMED) so cleaning tasks run in parallel with other setup activities rather than sequentially.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 60.0 min · as reported: “Storage conveyor cleaning”
    Show verbatim quote
    Storage conveyor cleaning 60 minutes
  2. Lost time: 324 min · as reported: “Cleaning of conveyors”
    Show verbatim quote
    Cleaning of conveyors 324 minutes