foratvise
Get Started
Setup and adjustments

Deflector position adjustment

Setup and adjustmentsAvailabilityMilling and grinding

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 56 % of the line's lost time. Reported by 1 of the 43 studies that could observe it (sparse evidence).

What happens

When a product or format change occurs, the deflector plate inside the milling (fibrizer) unit must be repositioned or re-angled to suit the new feed characteristics, so the equipment is taken out of production while operators manually loosen, move and re-secure the deflector and verify the new setting before resuming the run.

What is done about it

Apply SMED principles to the deflector adjustment: install calibrated scales, quick-release clamps or pre-set stops for each product format, and where feasible replace manual positioning with a motorized or guided actuator so the setting can be changed and verified without extended manual intervention.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.8% [0.1–2.3%]
Expected share of lost time
0.4% [0.1–1.3%]
Share of lost time when present
56% [43–67%]
Studies / units
43 / 48
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.9% [0.1–3.7%]5 studies
  • Soft drinks, bottled water and juices
    0.9% [0.1–3.8%]1 study
  • Brewing, wine and spirits
    1.0% [0.1–4.0%]0 studies
  • Bakery and pasta
    1.0% [0.1–3.8%]0 studies
  • Meat, poultry and seafood
    1.0% [0.1–3.8%]0 studies
  • Fruit and vegetable processing
    0.9% [0.1–3.5%]2 studies
  • Grain and oilseed milling
    0.9% [0.1–3.6%]7 studies
  • Sugar and confectionery
    1.3% [0.1–4.5%]10 studies
  • Snacks, coffee, tea and other foods
    0.9% [0.1–3.3%]5 studies
  • Animal feed and pet food
    0.9% [0.1–3.4%]6 studies
  • Food manufacturing (unspecified or mixed)
    0.9% [0.1–3.3%]7 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

When a product or format change occurs, the deflector plate inside the milling (fibrizer) unit must be repositioned or re-angled to suit the new feed characteristics, so the equipment is taken out of production while operators manually loosen, move and re-secure the deflector and verify the new setting before resuming the run.

How it looks in SCADA data

Engineering guidance

The line shows an extended setup or manual-mode state on the milling station with the drive motor stopped and zero throughput counts, often preceded by a changeover or product-code change event; the state duration is longer and more variable than typical minor stops, with no fault alarm raised.

Countermeasure

Engineering guidance

Apply SMED principles to the deflector adjustment: install calibrated scales, quick-release clamps or pre-set stops for each product format, and where feasible replace manual positioning with a motorized or guided actuator so the setting can be changed and verified without extended manual intervention.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 5.94 h · as reported: “Setup and Adjustment”
    Show verbatim quote
    Jumlah 5,94 5,94 0,00 0,00 0,00 16,20