foratvise
Get Started
Equipment failure (breakdowns)

Drive/inverter cooling fan failure

Equipment failure (breakdowns)AvailabilityMilling and grinding

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 0 of the 43 studies that could observe it (sparse evidence).

What happens

The cooling fan mounted on the mill drive/inverter degrades (worn bearings, blocked blades, electrical fault) and no longer provides sufficient airflow over the power electronics. The resulting heat build-up causes the drive to overheat and trip, stopping the mill motor until the fan is repaired or replaced.

What is done about it

Apply preventive maintenance on drive cooling fans, including periodic inspection, cleaning of blades and heat-sink filters, and timely replacement based on condition rather than waiting for failure. Add continuous temperature or fan-status monitoring with early-warning alarms so the fan can be swapped during a planned stop before it causes an unplanned trip.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.6% [0.1–1.8%]
Expected share of lost time
0.3% [0.0–1.0%]
Share of lost time when present
57% [45–67%]
Studies / units
43 / 48
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.7% [0.1–2.8%]5 studies
  • Soft drinks, bottled water and juices
    0.7% [0.1–2.9%]1 study
  • Brewing, wine and spirits
    0.7% [0.1–2.9%]0 studies
  • Bakery and pasta
    0.7% [0.1–3.0%]0 studies
  • Meat, poultry and seafood
    0.7% [0.1–2.7%]0 studies
  • Fruit and vegetable processing
    0.7% [0.1–2.7%]2 studies
  • Grain and oilseed milling
    0.7% [0.1–2.9%]7 studies
  • Sugar and confectionery
    0.6% [0.1–2.5%]10 studies
  • Snacks, coffee, tea and other foods
    0.7% [0.1–2.6%]5 studies
  • Animal feed and pet food
    0.7% [0.1–2.6%]6 studies
  • Food manufacturing (unspecified or mixed)
    0.7% [0.1–2.6%]7 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The cooling fan mounted on the mill drive/inverter degrades (worn bearings, blocked blades, electrical fault) and no longer provides sufficient airflow over the power electronics. The resulting heat build-up causes the drive to overheat and trip, stopping the mill motor until the fan is repaired or replaced.

How it looks in SCADA data

Engineering guidance

SCADA shows a drive overtemperature or fan-fault alarm immediately preceding the mill motor stop, often with the inverter status changing to fault/trip and no corresponding process or safety interlock. Fan feedback/status signal (if monitored) drops out or shows abnormal current draw, and repeated stop events may correlate with rising ambient or cabinet temperature.

Countermeasure

Engineering guidance

Apply preventive maintenance on drive cooling fans, including periodic inspection, cleaning of blades and heat-sink filters, and timely replacement based on condition rather than waiting for failure. Add continuous temperature or fan-status monitoring with early-warning alarms so the fan can be swapped during a planned stop before it causes an unplanned trip.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 1.00 Hr · as reported: “V4: Mill inverter fan blower problem”
    Show verbatim quote
    08/29/16 016602-01 V4: Mill inverter fan blower problem CMU 0 1 1