foratvise
Get Started
Equipment failure (breakdowns)

Dryer equipment malfunction and downtime

Equipment failure (breakdowns)AvailabilityDrying

In short

It appears in about 4 of every 100 lines studied.

When it appears, it takes on average about 58 % of the line's lost time. Reported by 4 of the 28 studies that could observe it (limited evidence).

What happens

Mechanical, electrical or pneumatic components of the dryer (fans, burners, conveyors, bearings, heating elements) wear out or fail, causing the machine to stop unexpectedly or requiring extended preparation and warm-up before stable operation is reached. While the dryer is down or not yet at operating temperature, product can be left under- or over-dried, producing drying losses in addition to the lost machine time.

What is done about it

Implement condition-based and preventive maintenance on critical dryer components, keep critical spare parts available, and standardize startup/preparation procedures to shorten warm-up time and stabilize drying conditions faster. Monitor key process variables to detect degradation trends before they cause unplanned stops or out-of-spec drying.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
3.6% [0.9–9.2%]
Expected share of lost time
2.1% [0.5–5.4%]
Share of lost time when present
58% [48–69%]
Studies / units
28 / 32
Evidence grade
C

Grade C: 2 to 4 studies, or an interval wider than 0.35.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    3.8% [0.5–12.6%]5 studies
  • Soft drinks, bottled water and juices
    4.1% [0.5–14.3%]1 study
  • Brewing, wine and spirits
    4.3% [0.5–15.1%]0 studies
  • Bakery and pasta
    4.4% [0.5–15.3%]0 studies
  • Meat, poultry and seafood
    4.2% [0.5–14.4%]0 studies
  • Fruit and vegetable processing
    4.0% [0.5–13.2%]2 studies
  • Grain and oilseed milling
    6.2% [0.7–22.4%]1 study
  • Sugar and confectionery
    5.1% [0.8–15.2%]4 studies
  • Snacks, coffee, tea and other foods
    5.2% [0.7–16.7%]4 studies
  • Animal feed and pet food
    5.4% [0.7–18.0%]4 studies
  • Food manufacturing (unspecified or mixed)
    3.7% [0.5–12.0%]7 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Mechanical, electrical or pneumatic components of the dryer (fans, burners, conveyors, bearings, heating elements) wear out or fail, causing the machine to stop unexpectedly or requiring extended preparation and warm-up before stable operation is reached. While the dryer is down or not yet at operating temperature, product can be left under- or over-dried, producing drying losses in addition to the lost machine time.

How it looks in SCADA data

Engineering guidance

SCADA/MES shows the dryer state switching from running to fault or idle with associated alarm codes, prolonged preparation/warm-up state durations before the first good batch, and process variables such as air temperature, airflow or burner status deviating from setpoint just before the stop. Moisture content readings or quality checks taken around these events often drift outside specification.

Countermeasure

Engineering guidance

Implement condition-based and preventive maintenance on critical dryer components, keep critical spare parts available, and standardize startup/preparation procedures to shorten warm-up time and stabilize drying conditions faster. Monitor key process variables to detect degradation trends before they cause unplanned stops or out-of-spec drying.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Defect rate: 7.13 % · as reported: “loss during drying (box dryer)”
    Show verbatim quote
    Lost during drying was 2.77 for sun drying compared to 7.13% with box dryer.
  2. Defect rate: 2.77 % · as reported: “loss during drying (sun drying)”
    Show verbatim quote
    Lost during drying was 2.77 for sun drying compared to 7.13% with box dryer.
  3. Lost time: 0.598 Kg.h-1 · as reported: “Drying sector (corn grains)”
    Show verbatim quote
    Drying 34 0.018 ± 0.003 0.598 ± 0.102 Kg 1.33
  4. Share of loss events: 39.0 % · as reported: “normal wear and tear”
    Show verbatim quote
    Penyebab terjadinya kerusakan mesin terbesar adalah kategori normal wear and tear sebanyak 39% dari total kerusakan yang terjadi di area kerja kritis.
  5. Lost time: 30.5 hours · as reported: “Machine Preparation Time”
    Show verbatim quote
    January 30.5 24.5 689 96
  6. Lost time: 33.3 hours · as reported: “Machine Preparation Time”
    Show verbatim quote
    March 33.33 10.67 700 98
  7. Lost time: 29.0 hours · as reported: “Machine Preparation Time”
    Show verbatim quote
    April 29 0 691 100
  8. Lost time: 24.5 hours · as reported: “Machine Downtime”
    Show verbatim quote
    January 30.5 24.5 689 96
  9. Lost time: 0 hours · as reported: “Machine Downtime”
    Show verbatim quote
    February 30.5 0 641.5 100
  10. Lost time: 10.7 hours · as reported: “Machine Downtime”
    Show verbatim quote
    March 33.33 10.67 700 98
  11. Lost time: 245 hours · as reported: “unexpected downtime”
    Show verbatim quote
    along with 245 hours of unexpected downtime in January, indicated losses caused by restart delays and reactive maintenance.