foratvise
Get Started
Process defects (scrap and rework)

Milling yield loss from drying-induced grain fissuring

Process defects (scrap and rework)QualityMilling and grinding

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 48 % of the line's lost time. Reported by 1 of the 43 studies that could observe it (sparse evidence).

What happens

Uneven or excessive moisture removal during pre-milling drying (whether by mechanical box dryer or sun drying) creates internal stress gradients in the kernel, producing micro-fissures and weak points. When these fissured kernels pass through the milling rolls or hullers, they fracture into broken grains and fines instead of yielding whole milled grain, lowering head rice yield and increasing downgraded by-product.

What is done about it

Standardize and control the drying process (controlled drying rate, tempering/moisture equalization steps, avoidance of abrupt temperature or humidity gradients) to minimize internal kernel stress before milling, and monitor grain moisture uniformity as an input quality gate to milling.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.9% [0.2–2.7%]
Expected share of lost time
0.4% [0.1–1.3%]
Share of lost time when present
48% [36–60%]
Studies / units
43 / 48
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    1.1% [0.1–4.1%]5 studies
  • Soft drinks, bottled water and juices
    1.1% [0.1–4.4%]1 study
  • Brewing, wine and spirits
    1.1% [0.1–4.4%]0 studies
  • Bakery and pasta
    1.1% [0.1–4.7%]0 studies
  • Meat, poultry and seafood
    1.1% [0.1–4.3%]0 studies
  • Fruit and vegetable processing
    1.1% [0.1–4.6%]2 studies
  • Grain and oilseed milling
    1.5% [0.1–5.7%]7 studies
  • Sugar and confectionery
    1.0% [0.1–3.7%]10 studies
  • Snacks, coffee, tea and other foods
    1.0% [0.1–3.9%]5 studies
  • Animal feed and pet food
    1.0% [0.1–3.8%]6 studies
  • Food manufacturing (unspecified or mixed)
    1.0% [0.1–3.9%]7 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Uneven or excessive moisture removal during pre-milling drying (whether by mechanical box dryer or sun drying) creates internal stress gradients in the kernel, producing micro-fissures and weak points. When these fissured kernels pass through the milling rolls or hullers, they fracture into broken grains and fines instead of yielding whole milled grain, lowering head rice yield and increasing downgraded by-product.

How it looks in SCADA data

Engineering guidance

Milling yield/output reports show a lower proportion of whole (head) rice and a higher proportion of broken rice and bran fines relative to input paddy weight, with batch-to-batch variability correlated to drying method or drying batch records. Moisture sensors upstream may show inconsistent or out-of-range readings preceding affected milling runs.

Countermeasure

Engineering guidance

Standardize and control the drying process (controlled drying rate, tempering/moisture equalization steps, avoidance of abrupt temperature or humidity gradients) to minimize internal kernel stress before milling, and monitor grain moisture uniformity as an input quality gate to milling.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Defect rate: 4.99 % · as reported: “milling losses (box dryer)”
    Show verbatim quote
    For milling losses, box dryer (4.99%) was lower than sun drying (5.99%).
  2. Defect rate: 5.99 % · as reported: “milling losses (sun drying)”
    Show verbatim quote
    For milling losses, box dryer (4.99%) was lower than sun drying (5.99%).