foratvise
Get Started
Process defects (scrap and rework)

Excessive polishing machine pressure

Process defects (scrap and rework)QualityWhole line or unspecified equipment

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 48 % of the line's lost time. Reported by 1 of the 127 studies that could observe it (sparse evidence).

What happens

The polishing machine is operated with a pressure setting, and consequently a per-batch cycle time, that exceeds what the product can tolerate, causing surface abrasion, breakage or other mechanical damage to the units or sacks being processed. The longer the product is held under high pressure during the processing cycle, the greater the proportion of damaged, downgraded or rejected material produced.

What is done about it

Define and enforce a validated pressure and cycle-time setpoint range for the polishing step based on product sensitivity, with automatic alarms or interlocks when values drift outside the range. Periodically verify pressure calibration and train operators to adjust settings per product type rather than applying a single universal setting.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.5% [0.1–1.4%]
Expected share of lost time
0.3% [0.1–0.7%]
Share of lost time when present
48% [36–60%]
Studies / units
127 / 161
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.1–2.3%]13 studies
  • Soft drinks, bottled water and juices
    0.6% [0.1–1.9%]26 studies
  • Brewing, wine and spirits
    0.6% [0.1–2.3%]11 studies
  • Bakery and pasta
    0.6% [0.1–1.9%]24 studies
  • Meat, poultry and seafood
    0.6% [0.1–2.3%]9 studies
  • Fruit and vegetable processing
    0.6% [0.1–2.2%]7 studies
  • Grain and oilseed milling
    0.9% [0.1–3.4%]6 studies
  • Sugar and confectionery
    0.6% [0.1–2.1%]9 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.1–2.2%]5 studies
  • Animal feed and pet food
    0.6% [0.1–2.2%]7 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.1–2.2%]10 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The polishing machine is operated with a pressure setting, and consequently a per-batch cycle time, that exceeds what the product can tolerate, causing surface abrasion, breakage or other mechanical damage to the units or sacks being processed. The longer the product is held under high pressure during the processing cycle, the greater the proportion of damaged, downgraded or rejected material produced.

How it looks in SCADA data

Engineering guidance

Pressure or torque sensor readings on the polishing unit trend above the normal operating band while the machine remains in run state, and the sack or batch cycle-time counter lengthens relative to standard cycles. These trends correlate with a rise in downstream reject, rework or downgrade counts recorded by quality or inspection stations without any corresponding equipment fault alarm.

Countermeasure

Engineering guidance

Define and enforce a validated pressure and cycle-time setpoint range for the polishing step based on product sensitivity, with automatic alarms or interlocks when values drift outside the range. Periodically verify pressure calibration and train operators to adjust settings per product type rather than applying a single universal setting.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Defect rate: 15.0 % · as reported: “excessive machine pressure”
    Show verbatim quote
    Waste Rate (%) – Excessive Machine Pressure TPM 15% 5% – 11% 7% (Pilot Est.)
  2. Mean event duration: 7.80 min · as reported: “sack processing cycle time”
    Show verbatim quote
    The AS IS scenario exhibited an average system time of 7.8 minutes, with a confidence interval of (7.55; 8.05)
  3. Defect rate: 7.00 % · as reported: “excessive machine pressure”
    Show verbatim quote
    7% (Pilot Est.)