foratvise
Get Started
Equipment failure (breakdowns)

Feed system failure

Equipment failure (breakdowns)AvailabilityMilling and grinding

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 0 of the 43 studies that could observe it (sparse evidence).

What happens

The mechanism that feeds raw material into the mill (screw conveyor, hopper feeder, rotary valve or metering device) loses its function due to mechanical wear, jamming of the drive, blockage by product build-up, or failure of its motor or coupling, so material stops reaching the grinding unit at the required rate. This forces the mill to stop or run empty until the feeding equipment is repaired or cleared by maintenance.

What is done about it

Apply preventive maintenance to the feeder drive, bearings and couplings, install sensors to detect blockage or no-flow conditions early, and design hoppers and chutes to minimize bridging or compaction of the material. Keep critical feeder spare parts available and train operators to clear minor obstructions without waiting for a full maintenance intervention.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.6% [0.1–1.8%]
Expected share of lost time
0.3% [0.0–1.1%]
Share of lost time when present
57% [46–68%]
Studies / units
43 / 48
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.7% [0.1–2.9%]5 studies
  • Soft drinks, bottled water and juices
    0.7% [0.1–3.0%]1 study
  • Brewing, wine and spirits
    0.7% [0.1–2.9%]0 studies
  • Bakery and pasta
    0.7% [0.1–2.9%]0 studies
  • Meat, poultry and seafood
    0.7% [0.1–2.8%]0 studies
  • Fruit and vegetable processing
    0.7% [0.1–2.9%]2 studies
  • Grain and oilseed milling
    0.7% [0.1–2.8%]7 studies
  • Sugar and confectionery
    0.6% [0.1–2.6%]10 studies
  • Snacks, coffee, tea and other foods
    0.7% [0.1–2.9%]5 studies
  • Animal feed and pet food
    0.7% [0.1–2.7%]6 studies
  • Food manufacturing (unspecified or mixed)
    0.7% [0.1–2.7%]7 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The mechanism that feeds raw material into the mill (screw conveyor, hopper feeder, rotary valve or metering device) loses its function due to mechanical wear, jamming of the drive, blockage by product build-up, or failure of its motor or coupling, so material stops reaching the grinding unit at the required rate. This forces the mill to stop or run empty until the feeding equipment is repaired or cleared by maintenance.

How it looks in SCADA data

Engineering guidance

SCADA/MES shows the feeder motor current or speed signal dropping to zero or to an abnormal value while the mill drive continues running, often accompanied by a low-level or no-flow alarm on the feed hopper and an unplanned downtime state logged against the feeding equipment. Repeated short-to-long stop events on the feeder, combined with starvation of the mill downstream, are typical of this failure mode.

Countermeasure

Engineering guidance

Apply preventive maintenance to the feeder drive, bearings and couplings, install sensors to detect blockage or no-flow conditions early, and design hoppers and chutes to minimize bridging or compaction of the material. Keep critical feeder spare parts available and train operators to clear minor obstructions without waiting for a full maintenance intervention.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Number of events: 36.0 events · as reported: “System feeding”
    Show verbatim quote
    Alimentação do sistema 36 146,1 221,5 49060,6 55,5
  2. Mean event duration: 146 min · as reported: “System feeding”
    Show verbatim quote
    Alimentação do sistema 36 146,1 221,5 49060,6 55,5