foratvise
Get Started
Process defects (scrap and rework)

Fill level and label adhesion nonconformance

Process defects (scrap and rework)QualityWhole line or unspecified equipment

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 48 % of the line's lost time. Reported by 1 of the 127 studies that could observe it (sparse evidence).

What happens

During otherwise stable production, variability in volumetric or weight dosing at the filler and in adhesive application, tension or alignment at the labeler causes individual units to fall outside the accepted fill-level and label-adhesion specifications. Both defects arise from drift in process parameters rather than from a stoppage, so the units are produced but not first-pass conforming.

What is done about it

Recalibrate and verify the filler dosing system (valves, pumps, load cells) and the labeler application parameters (adhesive temperature, tension, sensor alignment) on a scheduled basis, and implement statistical process control on fill weight and label placement with periodic manual verification to detect drift before units leave specification.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.5% [0.1–1.4%]
Expected share of lost time
0.2% [0.0–0.7%]
Share of lost time when present
48% [36–60%]
Studies / units
127 / 161
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.1–2.1%]13 studies
  • Soft drinks, bottled water and juices
    0.8% [0.1–2.6%]26 studies
  • Brewing, wine and spirits
    0.6% [0.1–2.1%]11 studies
  • Bakery and pasta
    0.6% [0.1–1.9%]24 studies
  • Meat, poultry and seafood
    0.6% [0.1–2.2%]9 studies
  • Fruit and vegetable processing
    0.6% [0.1–2.2%]7 studies
  • Grain and oilseed milling
    0.6% [0.1–2.3%]6 studies
  • Sugar and confectionery
    0.6% [0.1–2.2%]9 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.1–2.3%]5 studies
  • Animal feed and pet food
    0.6% [0.1–2.2%]7 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.1–2.2%]10 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

During otherwise stable production, variability in volumetric or weight dosing at the filler and in adhesive application, tension or alignment at the labeler causes individual units to fall outside the accepted fill-level and label-adhesion specifications. Both defects arise from drift in process parameters rather than from a stoppage, so the units are produced but not first-pass conforming.

How it looks in SCADA data

Engineering guidance

Checkweigher or fill-level sensor readings trend toward or beyond control limits while the line remains in run state, and label vision-inspection systems show rising reject or flag counts without corresponding downtime events. Reject diverter actuations and rework/scrap counters increase while machine-state logs show no stoppage, indicating a quality rather than an availability issue.

Countermeasure

Engineering guidance

Recalibrate and verify the filler dosing system (valves, pumps, load cells) and the labeler application parameters (adhesive temperature, tension, sensor alignment) on a scheduled basis, and implement statistical process control on fill weight and label placement with periodic manual verification to detect drift before units leave specification.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Defect rate: 2.00 % · as reported: “Label adhesion, fill level variance”
    Show verbatim quote
    June 112,000 2,240 Label adhesion, fill level variance 2.0 Corrective maintenance