foratvise
Get Started
Equipment failure (breakdowns)

Minor mechanical adjustment stop on filler

Equipment failure (breakdowns)AvailabilityFilling

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 1 of the 120 studies that could observe it (sparse evidence).

What happens

Wear, drift or misalignment of filler components such as valves, nozzles, pistons or guides gradually degrades dosing or positioning accuracy, forcing the operator or technician to stop the machine and perform a short mechanical correction. These interventions are brief but require hands-on access to the equipment rather than a simple reset, distinguishing them from a cleared jam.

What is done about it

Apply condition-based maintenance on the components most prone to drift (valve seals, dosing pistons, nozzle alignment), using vibration, position or weight-check data to schedule corrections before they cause a stop. Standardize quick-adjustment procedures with calibrated tools and track recurrence by component to target root-cause redesign or part replacement.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.5% [0.1–1.4%]
Expected share of lost time
0.3% [0.1–0.9%]
Share of lost time when present
57% [46–68%]
Studies / units
120 / 162
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.1–2.0%]18 studies
  • Soft drinks, bottled water and juices
    0.7% [0.1–2.1%]44 studies
  • Brewing, wine and spirits
    0.6% [0.1–2.2%]16 studies
  • Bakery and pasta
    0.7% [0.1–2.3%]0 studies
  • Meat, poultry and seafood
    0.6% [0.1–2.3%]6 studies
  • Fruit and vegetable processing
    0.7% [0.1–2.4%]4 studies
  • Grain and oilseed milling
    0.6% [0.1–2.3%]6 studies
  • Sugar and confectionery
    0.7% [0.1–2.4%]3 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.1–2.4%]6 studies
  • Animal feed and pet food
    0.7% [0.1–2.5%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.1–2.4%]13 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Wear, drift or misalignment of filler components such as valves, nozzles, pistons or guides gradually degrades dosing or positioning accuracy, forcing the operator or technician to stop the machine and perform a short mechanical correction. These interventions are brief but require hands-on access to the equipment rather than a simple reset, distinguishing them from a cleared jam.

How it looks in SCADA data

Engineering guidance

SCADA logs show frequent short stop events on the filler state, typically a few minutes each, often tagged with a fault or maintenance-call code rather than a jam or sensor-blocked alarm. Repeated recurrence of similar short downtime entries at the same station over a shift is characteristic, with no corresponding upstream or downstream starvation/blocking pattern.

Countermeasure

Engineering guidance

Apply condition-based maintenance on the components most prone to drift (valve seals, dosing pistons, nozzle alignment), using vibration, position or weight-check data to schedule corrections before they cause a stop. Standardize quick-adjustment procedures with calibrated tools and track recurrence by component to target root-cause redesign or part replacement.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of lost time: 61.0 % · as reported: “Short mechanical interventions in the filler for small adjustments (3-15 min interval)”
    Show verbatim quote
    the major occurrences of line downtimes consumed between 3 and 15 minutes of production, in equivalent proportions, summing 287 minutes (61% of the whole time) and characterizing the effectuation of short mechanical interventions in the filler for small adjustments (Figure 3).
  2. Lost time: 287 min · as reported: “Short mechanical interventions in the filler for small adjustments (3-15 min interval)”
    Show verbatim quote
    the major occurrences of line downtimes consumed between 3 and 15 minutes of production, in equivalent proportions, summing 287 minutes (61% of the whole time) and characterizing the effectuation of short mechanical interventions in the filler for small adjustments (Figure 3).