foratvise
Get Started
Start-up losses (reduced yield)

Filler start-up yield loss

Start-up losses (reduced yield)QualityFilling

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 47 % of the line's lost time. Reported by 0 of the 120 studies that could observe it (sparse evidence).

What happens

During the ramp-up of the filling machine after a stop, changeover or line start, fill valves, dosing pumps and level/weight controls have not yet stabilised, so containers are under-filled, over-filled or run empty before the setpoint is reached. Product used to prime lines, displace air or flush the product-water interface is diverted to drain or scrap rather than into saleable packs.

What is done about it

Standardise and automate the start-up sequence with recipe-driven ramp profiles for valves and pumps, use in-line sensors to detect when fill parameters are within tolerance before accepting packs as good, and minimise product lost to priming or interface flushing through recirculation or smaller dedicated flush volumes.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.3% [0.0–1.0%]
Expected share of lost time
0.1% [0.0–0.5%]
Share of lost time when present
47% [28–65%]
Studies / units
120 / 162
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.4% [0.0–1.4%]18 studies
  • Soft drinks, bottled water and juices
    0.3% [0.0–1.1%]44 studies
  • Brewing, wine and spirits
    0.4% [0.0–1.4%]16 studies
  • Bakery and pasta
    0.4% [0.0–1.6%]0 studies
  • Meat, poultry and seafood
    0.4% [0.0–1.5%]6 studies
  • Fruit and vegetable processing
    0.4% [0.0–1.5%]4 studies
  • Grain and oilseed milling
    0.4% [0.0–1.5%]6 studies
  • Sugar and confectionery
    0.4% [0.0–1.6%]3 studies
  • Snacks, coffee, tea and other foods
    0.4% [0.0–1.5%]6 studies
  • Animal feed and pet food
    0.4% [0.0–1.5%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.4% [0.0–1.5%]13 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

During the ramp-up of the filling machine after a stop, changeover or line start, fill valves, dosing pumps and level/weight controls have not yet stabilised, so containers are under-filled, over-filled or run empty before the setpoint is reached. Product used to prime lines, displace air or flush the product-water interface is diverted to drain or scrap rather than into saleable packs.

How it looks in SCADA data

Engineering guidance

SCADA shows the filler in a start-up or warm-up machine state preceding the stable-run state, with fill weight/level or flow signals outside control limits during the first cycles, elevated reject or recirculation counts coincident with this state, and a gap between total product metered and good packs produced immediately after each restart.

Countermeasure

Engineering guidance

Standardise and automate the start-up sequence with recipe-driven ramp profiles for valves and pumps, use in-line sensors to detect when fill parameters are within tolerance before accepting packs as good, and minimise product lost to priming or interface flushing through recirculation or smaller dedicated flush volumes.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 99.0 min · as reported: “Reduced Yield”
    Show verbatim quote
    Reduced Yield 99 1,4 100
  2. Share of lost time: 1.40 % · as reported: “Reduced Yield”
    Show verbatim quote
    Reduced Yield 99 1,4 100