foratvise
Get Started
Process defects (scrap and rework)

Filling and closure defects (underfill, uncrowned, contamination)

Process defects (scrap and rework)QualityFilling

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 49 % of the line's lost time. Reported by 1 of the 120 studies that could observe it (sparse evidence).

What happens

During the filling and crowning sequence, deviations in fill-valve dosing or level sensing leave bottles below the target fill height, while misalignment or malfunction of the crowning head leaves containers without a properly seated closure. Open or improperly closed containers passing through the line can also pick up foreign matter or microbial contamination before the closure seats.

What is done about it

Calibrate and periodically verify fill-valve dosing and level sensors, and maintain crowning head alignment, torque and feed timing through preventive maintenance. Reinforce sanitary barriers, air curtains and container handling to minimize exposure of open containers to contamination sources.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.5% [0.1–1.5%]
Expected share of lost time
0.3% [0.1–0.7%]
Share of lost time when present
49% [38–61%]
Studies / units
120 / 162
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.1–2.2%]18 studies
  • Soft drinks, bottled water and juices
    0.7% [0.1–2.1%]44 studies
  • Brewing, wine and spirits
    0.6% [0.1–2.1%]16 studies
  • Bakery and pasta
    0.7% [0.1–2.6%]0 studies
  • Meat, poultry and seafood
    0.6% [0.1–2.4%]6 studies
  • Fruit and vegetable processing
    0.6% [0.1–2.4%]4 studies
  • Grain and oilseed milling
    0.6% [0.1–2.3%]6 studies
  • Sugar and confectionery
    0.6% [0.1–2.4%]3 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.1–2.3%]6 studies
  • Animal feed and pet food
    0.6% [0.1–2.6%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.1–2.3%]13 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

During the filling and crowning sequence, deviations in fill-valve dosing or level sensing leave bottles below the target fill height, while misalignment or malfunction of the crowning head leaves containers without a properly seated closure. Open or improperly closed containers passing through the line can also pick up foreign matter or microbial contamination before the closure seats.

How it looks in SCADA data

Engineering guidance

Fill-level or weight readings trending below the lower control limit on the filler, combined with crowner reject or jam counters rising and inspection/checkweigher reject rates spiking for the same batch window. Correlated alarms on filler valve timing and crowner torque or position sensors help pinpoint the source machine.

Countermeasure

Engineering guidance

Calibrate and periodically verify fill-valve dosing and level sensors, and maintain crowning head alignment, torque and feed timing through preventive maintenance. Reinforce sanitary barriers, air curtains and container handling to minimize exposure of open containers to contamination sources.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of loss events: 88.1 % · as reported: “underfill, uncrowned bottles, and contamination”
    Show verbatim quote
    Pareto analysis revealed underfilling, uncrowned bottles, and contamination as the top contributors to scrap, accounting for 88.1% of total rejects.