foratvise
Get Started
Setup and adjustments

First-piece inspection after changeover

Setup and adjustmentsAvailabilityFilling

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 54 % of the line's lost time. Reported by 0 of the 120 studies that could observe it (sparse evidence).

What happens

After a format or product changeover, production cannot resume at full rate until the first produced unit is checked against specification (fill level, seal, dimensions, print). This verification step, whether manual or semi-automatic, consumes time between the end of the mechanical changeover and the first accepted good unit, extending the overall setup window.

What is done about it

Standardize first-piece verification with checklists, gauges or go/no-go fixtures to reduce subjectivity and time, and where feasible automate the check with in-line sensors (vision, checkweigher) that release the line without manual intervention; train operators on the specific acceptance criteria for each format to shorten decision time.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.3% [0.1–1.0%]
Expected share of lost time
0.2% [0.0–0.5%]
Share of lost time when present
54% [41–65%]
Studies / units
120 / 162
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.4% [0.0–1.5%]18 studies
  • Soft drinks, bottled water and juices
    0.3% [0.0–1.2%]44 studies
  • Brewing, wine and spirits
    0.4% [0.0–1.4%]16 studies
  • Bakery and pasta
    0.4% [0.0–1.6%]0 studies
  • Meat, poultry and seafood
    0.4% [0.0–1.5%]6 studies
  • Fruit and vegetable processing
    0.4% [0.0–1.6%]4 studies
  • Grain and oilseed milling
    0.4% [0.0–1.6%]6 studies
  • Sugar and confectionery
    0.4% [0.0–1.5%]3 studies
  • Snacks, coffee, tea and other foods
    0.4% [0.0–1.5%]6 studies
  • Animal feed and pet food
    0.4% [0.0–1.5%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.4% [0.0–1.6%]13 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

After a format or product changeover, production cannot resume at full rate until the first produced unit is checked against specification (fill level, seal, dimensions, print). This verification step, whether manual or semi-automatic, consumes time between the end of the mechanical changeover and the first accepted good unit, extending the overall setup window.

How it looks in SCADA data

Engineering guidance

Machine state remains in changeover or hold/check mode after the mechanical adjustment flag has already closed, with no production counts incrementing; MES logs show a discrete quality-check record or operator confirmation event inserted between changeover-end and run-start timestamps, sometimes repeated if the first piece fails and the cycle restarts.

Countermeasure

Engineering guidance

Standardize first-piece verification with checklists, gauges or go/no-go fixtures to reduce subjectivity and time, and where feasible automate the check with in-line sensors (vision, checkweigher) that release the line without manual intervention; train operators on the specific acceptance criteria for each format to shorten decision time.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 0.500 min · as reported: “Check on first piece”
    Show verbatim quote
    Check on first piece 0.5 min 17.5 min External
  2. Lost time: 0.500 min · as reported: “Check on first piece”
    Show verbatim quote
    Check on first piece | 0.5 min | 10.5 min | External