foratvise
Get Started
Process defects (scrap and rework)

Aluminum foil tearing

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 48 % of the line's lost time. Reported by 1 of the 112 studies that could observe it (sparse evidence).

What happens

During trimming or finishing of the aluminum foil wrap, excessive tension, misaligned guides, worn cutting edges or brittle/thin foil material cause the foil to tear instead of being cleanly cut or folded, producing a defective package that fails the seal or appearance specification.

What is done about it

Adjust and standardize foil tension and guide alignment, keep cutting blades or dies sharp and properly set, and verify incoming foil thickness and quality specifications to prevent tearing during trimming or finishing.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.6% [0.1–1.6%]
Expected share of lost time
0.3% [0.1–0.8%]
Share of lost time when present
48% [36–59%]
Studies / units
112 / 155
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.9% [0.1–3.3%]14 studies
  • Soft drinks, bottled water and juices
    0.5% [0.1–1.8%]33 studies
  • Brewing, wine and spirits
    0.6% [0.1–2.1%]14 studies
  • Bakery and pasta
    0.7% [0.1–2.5%]6 studies
  • Meat, poultry and seafood
    0.7% [0.1–2.6%]6 studies
  • Fruit and vegetable processing
    0.7% [0.1–2.4%]4 studies
  • Grain and oilseed milling
    0.7% [0.1–2.7%]4 studies
  • Sugar and confectionery
    0.7% [0.1–2.6%]4 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.1–2.3%]8 studies
  • Animal feed and pet food
    0.7% [0.1–2.5%]5 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.1–2.3%]14 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

During trimming or finishing of the aluminum foil wrap, excessive tension, misaligned guides, worn cutting edges or brittle/thin foil material cause the foil to tear instead of being cleanly cut or folded, producing a defective package that fails the seal or appearance specification.

How it looks in SCADA data

Engineering guidance

Rise in reject or scrap counts recorded at the foil trimming/finishing station, intermittent fault or vision-inspection alarms flagging torn or incomplete foil wraps, and short stoppages or operator interventions clustered around the trimming unit without a maintenance work order.

Countermeasure

Engineering guidance

Adjust and standardize foil tension and guide alignment, keep cutting blades or dies sharp and properly set, and verify incoming foil thickness and quality specifications to prevent tearing during trimming or finishing.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of loss events: 40.0 % · as reported: “sobek mesin”
    Show verbatim quote
    Terdapat tiga jenis reject yang dominan, yaitu sobek mesin (40,0%), lem (34,4%), dan penyok (22,9%).