Folding bracket assembly during changeover
In short
It appears in fewer than 1 of every 100 lines studied.
When it appears, it takes on average about 57 % of the line's lost time. Reported by 0 of the 112 studies that could observe it (sparse evidence).
What happens
During a format or component changeover the folding bracket of the carton/case folding module must be manually removed, fitted and aligned, including fastening and verification steps that are inherent to assembling this mechanical subassembly. Because the task depends on manual handling and precise positioning of the bracket relative to the folding mechanism, it adds non-value time to the changeover before the module can resume forming good packages.
What is done about it
Redesign the bracket for tool-less, quick-release mounting with guided locating features so it can be exchanged without fine manual alignment, and pre-kit or pre-assemble the component outside the line before the changeover window. Standardized work instructions and jigs for the assembly step further reduce variability and changeover duration.
Practical guidance written from engineering knowledge; it is not a statistical estimate.
1Probability and evidence
- Probability of presence
- 0.3% [0.1–1.0%]
- Expected share of lost time
- 0.2% [0.0–0.6%]
- Share of lost time when present
- 57% [44–67%]
- Studies / units
- 112 / 155
- Evidence grade
- D
Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.
2Probability by segment
- Dairy products0.4% [0.0–1.4%]14 studies
- Soft drinks, bottled water and juices0.4% [0.0–1.3%]33 studies
- Brewing, wine and spirits0.4% [0.0–1.6%]14 studies
- Bakery and pasta0.4% [0.0–1.6%]6 studies
- Meat, poultry and seafood0.4% [0.0–1.6%]6 studies
- Fruit and vegetable processing0.4% [0.0–1.6%]4 studies
- Grain and oilseed milling0.4% [0.0–1.7%]4 studies
- Sugar and confectionery0.4% [0.0–1.6%]4 studies
- Snacks, coffee, tea and other foods0.4% [0.0–1.6%]8 studies
- Animal feed and pet food0.4% [0.0–1.6%]5 studies
- Food manufacturing (unspecified or mixed)0.4% [0.0–1.5%]14 studies
3Mechanism, SCADA signature and countermeasure
Mechanism
Engineering guidanceDuring a format or component changeover the folding bracket of the carton/case folding module must be manually removed, fitted and aligned, including fastening and verification steps that are inherent to assembling this mechanical subassembly. Because the task depends on manual handling and precise positioning of the bracket relative to the folding mechanism, it adds non-value time to the changeover before the module can resume forming good packages.
How it looks in SCADA data
Engineering guidanceThe packaging module shows a prolonged changeover or manual/maintenance state with the folding station reporting no cycle counts while adjacent conveying and upstream filling stages accumulate or starve waiting for the module to restart. Machine-state logs typically show a single extended non-run segment tagged as setup rather than a fault alarm.
Countermeasure
Engineering guidanceRedesign the bracket for tool-less, quick-release mounting with guided locating features so it can be exchanged without fine manual alignment, and pre-kit or pre-assemble the component outside the line before the changeover window. Standardized work instructions and jigs for the assembly step further reduce variability and changeover duration.
4Sources
- Integrating SMED and Mechanical Design for Changeover Reduction in Beverage Packaging Lines (2026)Open sourceMean event duration: 78.5 % reduction · as reported: “Folding Bracket Assembly Task (Redesigned Component)”
Show verbatim quote
A redesigned tool-less folding bracket reduced its adjustment task time by 78.5% and its variance by 99.3% under statistically conclusive testing.

