foratvise
Get Started
Equipment failure (breakdowns)

Forming machine drive/chain mechanical failure

Equipment failure (breakdowns)AvailabilityForming, moulding and depositing

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 2 of the 76 studies that could observe it (limited evidence).

What happens

Mechanical drive components of the forming machine, such as the drive chain or actuating spring, suffer fatigue, wear or overload and eventually break or jam, interrupting the transmission of motion to the forming mechanism and stopping the cycle. The same mechanical fragility also manifests as generic downtime, as adjustments during setup after a repair, and as off-spec product while the machine restabilizes after a drive-related stoppage.

What is done about it

Establish a preventive maintenance program with scheduled inspection, lubrication and replacement of chains, springs and other drive components based on wear condition rather than failure, and keep critical spare parts available to shorten repair time. Reinforce drive guarding and overload protection, and standardize the post-repair startup procedure to shorten the adjustment and yield-loss period after a mechanical stoppage.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
1.1% [0.2–3.0%]
Expected share of lost time
0.6% [0.1–1.7%]
Share of lost time when present
57% [46–68%]
Studies / units
76 / 96
Evidence grade
C

Grade C: 2 to 4 studies, or an interval wider than 0.35.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    1.3% [0.1–4.9%]5 studies
  • Soft drinks, bottled water and juices
    1.2% [0.1–4.2%]11 studies
  • Brewing, wine and spirits
    1.3% [0.1–4.8%]0 studies
  • Bakery and pasta
    1.0% [0.1–3.6%]25 studies
  • Meat, poultry and seafood
    1.9% [0.2–7.3%]3 studies
  • Fruit and vegetable processing
    1.9% [0.2–7.1%]3 studies
  • Grain and oilseed milling
    1.3% [0.1–4.9%]0 studies
  • Sugar and confectionery
    1.2% [0.1–4.8%]8 studies
  • Snacks, coffee, tea and other foods
    1.2% [0.1–4.3%]7 studies
  • Animal feed and pet food
    1.2% [0.2–4.2%]6 studies
  • Food manufacturing (unspecified or mixed)
    1.3% [0.1–4.6%]8 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Mechanical drive components of the forming machine, such as the drive chain or actuating spring, suffer fatigue, wear or overload and eventually break or jam, interrupting the transmission of motion to the forming mechanism and stopping the cycle. The same mechanical fragility also manifests as generic downtime, as adjustments during setup after a repair, and as off-spec product while the machine restabilizes after a drive-related stoppage.

How it looks in SCADA data

Engineering guidance

SCADA/MES logs show an abrupt transition of the forming machine to a stopped or fault state with the cycle counter frozen, often coinciding with a drive motor overload, torque or tension alarm; downstream equipment shows starvation while the forming machine remains in a non-cycling fault state until manual mechanical intervention is recorded. Subsequent restart is followed by a setup/adjustment state and a transient run with elevated reject counts before stable output resumes.

Countermeasure

Engineering guidance

Establish a preventive maintenance program with scheduled inspection, lubrication and replacement of chains, springs and other drive components based on wear condition rather than failure, and keep critical spare parts available to shorten repair time. Reinforce drive guarding and overload protection, and standardize the post-repair startup procedure to shorten the adjustment and yield-loss period after a mechanical stoppage.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of lost time: 24.4 % · as reported: “yield losses”
    Show verbatim quote
    the three biggest factors that caused the low value of machine effectiveness were idling & minor stoppages losses of 24.61%, yield losses of 24.37%, and reduced speed losses of 23.78%
  2. Lost time: 193 menit · as reported: “setup”
    Show verbatim quote
    rata-rata 3.564 193,25 3.757,25
  3. Lost time: 3,757 menit · as reported: “downtime”
    Show verbatim quote
    rata-rata 3.564 193,25 3.757,25
  4. Mean event duration: 30.0 menit · as reported: “rantai putus”
    Show verbatim quote
    Dalam satu bulan, tercatat 2 hingga 3 kali kejadian rantai putus dengan rata-rata waktu penanganan sekitar 30 menit per kejadian, serta 10 hingga 15 kali kegiatan perawatan pada pir penggerak dengan rata-rata waktu perbaikan 15 menit.
  5. Mean event duration: 15.0 menit · as reported: “pir penggerak”
    Show verbatim quote
    Dalam satu bulan, tercatat 2 hingga 3 kali kejadian rantai putus dengan rata-rata waktu penanganan sekitar 30 menit per kejadian, serta 10 hingga 15 kali kegiatan perawatan pada pir penggerak dengan rata-rata waktu perbaikan 15 menit.