foratvise
Get Started
Reduced speed

Grinding mill component wear causing reduced throughput and scrap

Reduced speedPerformanceMilling and grinding

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 64 % of the line's lost time. Reported by 1 of the 43 studies that could observe it (sparse evidence).

What happens

Worn or degraded grinding components (plates, hammers, screens, media) inside the ICM grinding mill lose their cutting or crushing efficiency, so the mill cannot sustain its design throughput and must be run slower to maintain particle size. The same degraded action also lets oversized or unevenly sized particles pass through, generating off-spec material that is scrapped or reworked.

What is done about it

Implement condition-based inspection and timely replacement of grinding media, plates or screens, and recalibrate feed rate and gap settings to restore design throughput and particle-size specification.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
1.1% [0.2–3.6%]
Expected share of lost time
0.7% [0.1–2.3%]
Share of lost time when present
64% [50–76%]
Studies / units
43 / 48
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    1.3% [0.1–5.0%]5 studies
  • Soft drinks, bottled water and juices
    1.4% [0.1–5.7%]1 study
  • Brewing, wine and spirits
    1.4% [0.1–5.4%]0 studies
  • Bakery and pasta
    1.4% [0.1–5.3%]0 studies
  • Meat, poultry and seafood
    1.4% [0.1–5.8%]0 studies
  • Fruit and vegetable processing
    1.4% [0.1–5.3%]2 studies
  • Grain and oilseed milling
    1.3% [0.1–4.9%]7 studies
  • Sugar and confectionery
    1.8% [0.2–6.3%]10 studies
  • Snacks, coffee, tea and other foods
    1.3% [0.1–4.9%]5 studies
  • Animal feed and pet food
    1.3% [0.1–4.8%]6 studies
  • Food manufacturing (unspecified or mixed)
    1.3% [0.1–5.2%]7 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Worn or degraded grinding components (plates, hammers, screens, media) inside the ICM grinding mill lose their cutting or crushing efficiency, so the mill cannot sustain its design throughput and must be run slower to maintain particle size. The same degraded action also lets oversized or unevenly sized particles pass through, generating off-spec material that is scrapped or reworked.

How it looks in SCADA data

Engineering guidance

Mill motor load or current trends downward relative to feed rate while actual throughput or line speed sits persistently below the target setpoint; quality or particle-size inspection counters linked to the mill run show an elevated scrap or reject tally without a corresponding stoppage alarm.

Countermeasure

Engineering guidance

Implement condition-based inspection and timely replacement of grinding media, plates or screens, and recalibrate feed rate and gap settings to restore design throughput and particle-size specification.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of planned time: 9.00 % · as reported: “yield atau scrap loss”
    Show verbatim quote
    Rata-rata yang dihasilkan scrap loss yaitu 9%.
  2. Share of planned time: 41.0 % · as reported: “reduced speed loss”
    Show verbatim quote
    Rata-rata reduced speed losses mesin grinding pada bulan Juli sampai Desember 2021 yaitu 41%.