foratvise
Get Started
Equipment failure (breakdowns)

Gripper Failure

Equipment failure (breakdowns)AvailabilityFilling

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 0 of the 120 studies that could observe it (sparse evidence).

What happens

The mechanical gripper that picks up, transfers or positions containers at the filling station loses its ability to clamp or release correctly because of worn jaws or pads, fatigued springs, misaligned actuators, pneumatic leakage or accumulated debris. When the gripper fails to seize, center or let go of a container it causes a dropped, crooked or jammed unit that forces the station to stop until the mechanism is cleared or repaired.

What is done about it

Apply preventive maintenance on gripper jaws, pads and springs with scheduled replacement based on wear, inspect and recalibrate pneumatic cylinders or servo actuators, and keep the mechanism clean and lubricated. Verify grip-force and position sensors regularly and adjust guide rails or centering guides that feed containers into the gripper.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.4% [0.1–1.2%]
Expected share of lost time
0.2% [0.0–0.7%]
Share of lost time when present
57% [46–67%]
Studies / units
120 / 162
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.4% [0.0–1.7%]18 studies
  • Soft drinks, bottled water and juices
    0.4% [0.0–1.3%]44 studies
  • Brewing, wine and spirits
    0.4% [0.0–1.6%]16 studies
  • Bakery and pasta
    0.5% [0.0–1.9%]0 studies
  • Meat, poultry and seafood
    0.5% [0.0–1.8%]6 studies
  • Fruit and vegetable processing
    0.5% [0.0–1.8%]4 studies
  • Grain and oilseed milling
    0.5% [0.0–1.7%]6 studies
  • Sugar and confectionery
    0.5% [0.0–1.9%]3 studies
  • Snacks, coffee, tea and other foods
    0.5% [0.0–1.7%]6 studies
  • Animal feed and pet food
    0.5% [0.0–1.9%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.4% [0.0–1.8%]13 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The mechanical gripper that picks up, transfers or positions containers at the filling station loses its ability to clamp or release correctly because of worn jaws or pads, fatigued springs, misaligned actuators, pneumatic leakage or accumulated debris. When the gripper fails to seize, center or let go of a container it causes a dropped, crooked or jammed unit that forces the station to stop until the mechanism is cleared or repaired.

How it looks in SCADA data

Engineering guidance

SCADA/MES logs show fault or alarm codes tied specifically to the gripper or pick-and-place axis (position error, grip-force or proximity sensor fault), with the filler transitioning to a fault state while upstream conveyors fill up and downstream stations starve. The event recurs as isolated stops localized to the same station address rather than spreading uniformly across the line.

Countermeasure

Engineering guidance

Apply preventive maintenance on gripper jaws, pads and springs with scheduled replacement based on wear, inspect and recalibrate pneumatic cylinders or servo actuators, and keep the mechanism clean and lubricated. Verify grip-force and position sensors regularly and adjust guide rails or centering guides that feed containers into the gripper.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Number of events: 12.0 events · as reported: “Gripper”
    Show verbatim quote
    Gripper 12