foratvise
Get Started
Equipment failure (breakdowns)

Inadequate preventive maintenance (cleaning, lubrication, tensioning)

Equipment failure (breakdowns)AvailabilityDrying

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 1 of the 28 studies that could observe it (sparse evidence).

What happens

Routine upkeep tasks such as cleaning, lubrication and belt or chain tensioning are skipped or delayed on the dryer-cooler, allowing debris buildup, dry friction and mechanical slack to accumulate in drive and conveying components. Over time this accelerates wear, causes belt slippage, bearing overheating or component seizure, which eventually manifests as an unplanned equipment stoppage requiring repair.

What is done about it

Establish a structured preventive maintenance schedule with defined intervals for cleaning, lubrication and belt/chain tensioning aligned with OEM recommendations, and track compliance through the CMMS. Complement it with condition-based monitoring (vibration, temperature, current) on critical drive components to detect degradation early and trigger maintenance before an unplanned failure occurs.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
1.1% [0.2–3.3%]
Expected share of lost time
0.6% [0.1–1.9%]
Share of lost time when present
57% [46–67%]
Studies / units
28 / 32
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    1.3% [0.1–5.2%]5 studies
  • Soft drinks, bottled water and juices
    1.3% [0.1–5.4%]1 study
  • Brewing, wine and spirits
    1.3% [0.1–5.3%]0 studies
  • Bakery and pasta
    1.3% [0.1–5.2%]0 studies
  • Meat, poultry and seafood
    1.4% [0.1–5.7%]0 studies
  • Fruit and vegetable processing
    1.3% [0.1–5.0%]2 studies
  • Grain and oilseed milling
    1.3% [0.1–5.8%]1 study
  • Sugar and confectionery
    1.8% [0.2–6.8%]4 studies
  • Snacks, coffee, tea and other foods
    1.2% [0.1–4.8%]4 studies
  • Animal feed and pet food
    1.2% [0.1–4.7%]4 studies
  • Food manufacturing (unspecified or mixed)
    1.3% [0.1–4.8%]7 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Routine upkeep tasks such as cleaning, lubrication and belt or chain tensioning are skipped or delayed on the dryer-cooler, allowing debris buildup, dry friction and mechanical slack to accumulate in drive and conveying components. Over time this accelerates wear, causes belt slippage, bearing overheating or component seizure, which eventually manifests as an unplanned equipment stoppage requiring repair.

How it looks in SCADA data

Engineering guidance

SCADA/MES data show a gradual drift in drive motor current, torque or temperature trends prior to the stop, intermittent speed or vibration alarms, and an increasing frequency of short minor stops that escalate into a longer unplanned downtime event. Maintenance work-order logs typically reveal overdue or skipped cleaning, lubrication and tensioning tasks immediately before the failure.

Countermeasure

Engineering guidance

Establish a structured preventive maintenance schedule with defined intervals for cleaning, lubrication and belt/chain tensioning aligned with OEM recommendations, and track compliance through the CMMS. Complement it with condition-based monitoring (vibration, temperature, current) on critical drive components to detect degradation early and trigger maintenance before an unplanned failure occurs.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of loss events: 29.0 % · as reported: “lack of cleaning, loose tension, dan lack of lubrication”
    Show verbatim quote
    Penyebab kerusakan kedua sebesar 29% (lack of cleaning, loose tension, dan lack of lubrication) bisa diatasi jika program autonomous maintenance dijalankan.
  2. Share of lost time: 48.4 % · as reported: “mechanical failures due to the lack of preventive maintenance”
    Show verbatim quote
    mainly caused by mechanical failures due to the lack of preventive maintenance (48.4%), high levels of waste reprocessing (31.4%), and dosing deviations (3.4%)