foratvise
Get Started
Equipment failure (breakdowns)

Infeed screw/worm malfunction or jam

Equipment failure (breakdowns)AvailabilityFilling

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 58 % of the line's lost time. Reported by 2 of the 120 studies that could observe it (limited evidence).

What happens

The infeed worm/screw meters and spaces containers at a fixed pitch to hand them off to the filler; mechanical wear, loose or worn timing settings, electrical/drive faults, or containers wedging between the screw flights disrupt this metered flow. When the timing drifts or a mechanical trip occurs the unit stops feeding containers, and when containers jam physically between the screw and guide rails the infeed path blocks until cleared.

What is done about it

Perform preventive maintenance and periodic inspection of the infeed screw drive, bearings, and timing mechanism, recalibrating the worm timing to the container format in use; clear jams promptly and add or tune container-presence/guide sensors to reduce misfeeds and trips.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.7% [0.2–2.0%]
Expected share of lost time
0.4% [0.1–1.1%]
Share of lost time when present
58% [46–68%]
Studies / units
120 / 162
Evidence grade
C

Grade C: 2 to 4 studies, or an interval wider than 0.35.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.8% [0.1–2.7%]18 studies
  • Soft drinks, bottled water and juices
    1.2% [0.2–3.2%]44 studies
  • Brewing, wine and spirits
    0.8% [0.1–2.7%]16 studies
  • Bakery and pasta
    0.9% [0.1–3.4%]0 studies
  • Meat, poultry and seafood
    0.8% [0.1–2.8%]6 studies
  • Fruit and vegetable processing
    0.9% [0.1–3.2%]4 studies
  • Grain and oilseed milling
    0.9% [0.1–3.1%]6 studies
  • Sugar and confectionery
    0.9% [0.1–3.4%]3 studies
  • Snacks, coffee, tea and other foods
    0.8% [0.1–2.9%]6 studies
  • Animal feed and pet food
    0.9% [0.1–3.2%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.8% [0.1–2.9%]13 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The infeed worm/screw meters and spaces containers at a fixed pitch to hand them off to the filler; mechanical wear, loose or worn timing settings, electrical/drive faults, or containers wedging between the screw flights disrupt this metered flow. When the timing drifts or a mechanical trip occurs the unit stops feeding containers, and when containers jam physically between the screw and guide rails the infeed path blocks until cleared.

How it looks in SCADA data

Engineering guidance

SCADA/MES logs show infeed drive trip or fault alarms, screw motor stop states, and repeated short-duration downtime events tagged as jams at the infeed station, often accompanied by container-presence sensor flutter and downstream filler starvation (filler idle while waiting for containers).

Countermeasure

Engineering guidance

Perform preventive maintenance and periodic inspection of the infeed screw drive, bearings, and timing mechanism, recalibrating the worm timing to the container format in use; clear jams promptly and add or tune container-presence/guide sensors to reduce misfeeds and trips.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 71.0 min · as reported: “Infeed jam”
    Show verbatim quote
    Infeed jam 6 8 14 7 12 13 71 4.85
  2. Share of lost time: 4.85 % · as reported: “Infeed jam”
    Show verbatim quote
    Infeed jam 6 8 14 7 12 13 71 4.85
  3. Lost time: 16.0 min · as reported: “Infeed unit trip”
    Show verbatim quote
    Infeed unit trip 8 1 2 0 0 5 16 1.09
  4. Share of lost time: 1.09 % · as reported: “Infeed unit trip”
    Show verbatim quote
    Infeed unit trip 8 1 2 0 0 5 16 1.09
  5. Lost time: 28.0 min · as reported: “Infeed worm timing setting”
    Show verbatim quote
    Infeed worm timing setting 4 8 0 0 0 16 28 1.91
  6. Share of lost time: 1.91 % · as reported: “Infeed worm timing setting”
    Show verbatim quote
    Infeed worm timing setting 4 8 0 0 0 16 28 1.91
  7. Lost time: 5.00 min · as reported: “Infeed unit trip”
    Show verbatim quote
    14 | Infeed unit trip | 8 | 1 | 2 | 0 | 0 | 5 | 16 | 1.09
  8. Lost time: 16.0 min · as reported: “Infeed worm timing setting”
    Show verbatim quote
    15 | Infeed worm timing setting | 4 | 8 | 0 | 0 | 0 | 16 | 28 | 1.91
  9. Lost time: 623 min · as reported: “infeed screw”
    Show verbatim quote
    infeed screw 13 623 93 2888 83.03 82.14
  10. Number of events: 13.0 events · as reported: “infeed screw”
    Show verbatim quote
    infeed screw 13 623 93 2888 83.03 82.14