foratvise
Get Started
not classifiable

Transportation time between stations

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 59 % of the line's lost time. Reported by 1 of the 86 studies that could observe it (sparse evidence).

What happens

Product or containers require a finite travel time on conveyors or transfer paths between successive stations of the line, and this transit interval is counted as line time even though no processing occurs. The loss appears when conveyor layout, distance, or accumulation buffers make this transport interval long relative to the processing cycle, effectively idling downstream equipment while material is in transit.

What is done about it

Redesign conveyor layout to shorten transport paths and align conveyor speeds with upstream and downstream cycle times, adding buffering or accumulation sections where needed to decouple transit time from processing rate. Line balancing studies and relocation of equipment to reduce travel distance are the typical engineering response.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.7% [0.1–1.9%]
Expected share of lost time
0.4% [0.1–1.2%]
Share of lost time when present
59% [49–71%]
Studies / units
86 / 112
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.7% [0.1–2.6%]11 studies
  • Soft drinks, bottled water and juices
    0.6% [0.1–2.3%]28 studies
  • Brewing, wine and spirits
    0.7% [0.1–2.5%]12 studies
  • Bakery and pasta
    0.8% [0.1–3.0%]0 studies
  • Meat, poultry and seafood
    1.1% [0.1–4.4%]5 studies
  • Fruit and vegetable processing
    0.8% [0.1–3.0%]4 studies
  • Grain and oilseed milling
    0.8% [0.1–3.1%]4 studies
  • Sugar and confectionery
    0.8% [0.1–3.1%]4 studies
  • Snacks, coffee, tea and other foods
    0.8% [0.1–3.0%]4 studies
  • Animal feed and pet food
    0.8% [0.1–3.0%]5 studies
  • Food manufacturing (unspecified or mixed)
    0.8% [0.1–2.9%]9 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Product or containers require a finite travel time on conveyors or transfer paths between successive stations of the line, and this transit interval is counted as line time even though no processing occurs. The loss appears when conveyor layout, distance, or accumulation buffers make this transport interval long relative to the processing cycle, effectively idling downstream equipment while material is in transit.

How it looks in SCADA data

Engineering guidance

Logs show a distinct conveying or transit machine-state with a duration that does not correspond to any processing alarm, often paired with downstream starvation (waiting-for-material) states and upstream blocking states. No fault code is raised, and the pattern recurs cyclically with the line's material flow rather than as discrete stoppage events.

Countermeasure

Engineering guidance

Redesign conveyor layout to shorten transport paths and align conveyor speeds with upstream and downstream cycle times, adding buffering or accumulation sections where needed to decouple transit time from processing rate. Line balancing studies and relocation of equipment to reduce travel distance are the typical engineering response.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 10.0 min · as reported: “Transportation time”
    Show verbatim quote
    For the automated line, a reduction from 10 to 5 min was achieved which represents improvement by 50% in the transportation time.