foratvise
Get Started
Equipment failure (breakdowns)

Inverter/VFD fault or failure

Equipment failure (breakdowns)AvailabilityMilling and grinding

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 0 of the 43 studies that could observe it (sparse evidence).

What happens

The variable frequency drive that controls the mill motor develops an internal electrical or electronic fault, such as an overcurrent condition, overheating of power modules, or capacitor and component wear, which trips the drive and interrupts motor control. Such faults accumulate over time through thermal cycling, dust ingress, or inadequate cooling, eventually requiring corrective repair or scheduled service of the drive unit.

What is done about it

Apply preventive maintenance to the drive module including cleaning of ventilation paths, verification of cooling fan operation, and tightening of power connections, combined with trending of drive diagnostic parameters such as current, temperature, and fault history to detect degradation before a hard trip occurs. Keep spare drive units or power modules on hand and ensure the drive is correctly sized and derated for the mill load to reduce stress-related failures.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.6% [0.1–1.9%]
Expected share of lost time
0.3% [0.1–1.1%]
Share of lost time when present
57% [46–68%]
Studies / units
43 / 48
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.7% [0.1–2.7%]5 studies
  • Soft drinks, bottled water and juices
    0.7% [0.1–3.0%]1 study
  • Brewing, wine and spirits
    0.7% [0.1–3.0%]0 studies
  • Bakery and pasta
    0.7% [0.1–3.0%]0 studies
  • Meat, poultry and seafood
    0.7% [0.1–3.0%]0 studies
  • Fruit and vegetable processing
    0.7% [0.1–2.9%]2 studies
  • Grain and oilseed milling
    0.7% [0.1–2.9%]7 studies
  • Sugar and confectionery
    0.7% [0.1–2.5%]10 studies
  • Snacks, coffee, tea and other foods
    0.7% [0.1–2.6%]5 studies
  • Animal feed and pet food
    0.7% [0.1–2.8%]6 studies
  • Food manufacturing (unspecified or mixed)
    0.7% [0.1–2.7%]7 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The variable frequency drive that controls the mill motor develops an internal electrical or electronic fault, such as an overcurrent condition, overheating of power modules, or capacitor and component wear, which trips the drive and interrupts motor control. Such faults accumulate over time through thermal cycling, dust ingress, or inadequate cooling, eventually requiring corrective repair or scheduled service of the drive unit.

How it looks in SCADA data

Engineering guidance

The drive reports a specific fault or trip code (e.g. an overcurrent alarm) in the control system log, the drive state transitions abruptly to fault while the speed command remains active but the feedback speed drops to zero, and the mill motor stops while upstream feed accumulates or downstream stations starve. Maintenance work orders or planned-stop entries are logged against the identified drive asset tag, sometimes separate from the fault trip itself when service is scheduled proactively.

Countermeasure

Engineering guidance

Apply preventive maintenance to the drive module including cleaning of ventilation paths, verification of cooling fan operation, and tightening of power connections, combined with trending of drive diagnostic parameters such as current, temperature, and fault history to detect degradation before a hard trip occurs. Keep spare drive units or power modules on hand and ensure the drive is correctly sized and derated for the mill load to reduce stress-related failures.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Time between events: 2,806 Hr · as reported: “Variable frequency drive failure”
    Show verbatim quote
    Variable frequency drive failure - - 2806.00 2.00
  2. Mean event duration: 2.00 Hr · as reported: “Variable frequency drive failure”
    Show verbatim quote
    Variable frequency drive failure - - 2806.00 2.00
  3. Lost time: 3.00 Hr · as reported: “V4: Inverter 75kW (S/N 000001) error OC1”
    Show verbatim quote
    06/25/16 016132 V4: Inverter 75kW (S/N 000001) error OC1 CMU 0 3 3
  4. Lost time: 1.00 Hr · as reported: “V4: Inverter (DR-14) service”
    Show verbatim quote
    10/14/16 016694 V4: Inverter (DR-14) service PM 0 1 1