foratvise
Get Started
Equipment failure (breakdowns)

Label applicator jam or misfeed

Equipment failure (breakdowns)AvailabilityLabeling and coding

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 0 of the 85 studies that could observe it (sparse evidence).

What happens

Labels with excess adhesive stick to the backing web, dispensing plate or guide rails, while labels cut outside the correct length or with dimensional variation fail to register properly and get caught at the peel edge or applicator pads. The resulting tearing, folding or buildup of adhesive residue blocks the label path and stalls the applicator mechanism, so the fault must be cleared and the mechanism cleaned or adjusted before production can resume.

What is done about it

Control label stock quality and storage conditions to keep adhesive tack and die-cut dimensions within specification, and verify incoming reels against applicator tolerances before loading. Maintain and periodically clean the peel plate, rollers and sensors, and adjust tension, dispensing speed and sensor sensitivity to the specific label format in use.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.4% [0.1–1.4%]
Expected share of lost time
0.3% [0.0–0.8%]
Share of lost time when present
57% [46–68%]
Studies / units
85 / 113
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.5% [0.0–2.0%]11 studies
  • Soft drinks, bottled water and juices
    0.4% [0.0–1.5%]29 studies
  • Brewing, wine and spirits
    0.5% [0.0–1.9%]13 studies
  • Bakery and pasta
    0.6% [0.0–2.3%]1 study
  • Meat, poultry and seafood
    0.5% [0.0–2.1%]4 studies
  • Fruit and vegetable processing
    0.5% [0.1–2.0%]4 studies
  • Grain and oilseed milling
    0.5% [0.0–2.3%]3 studies
  • Sugar and confectionery
    0.5% [0.0–2.1%]3 studies
  • Snacks, coffee, tea and other foods
    0.5% [0.0–2.1%]4 studies
  • Animal feed and pet food
    0.5% [0.0–2.2%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.5% [0.0–2.2%]9 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Labels with excess adhesive stick to the backing web, dispensing plate or guide rails, while labels cut outside the correct length or with dimensional variation fail to register properly and get caught at the peel edge or applicator pads. The resulting tearing, folding or buildup of adhesive residue blocks the label path and stalls the applicator mechanism, so the fault must be cleared and the mechanism cleaned or adjusted before production can resume.

How it looks in SCADA data

Engineering guidance

MES/SCADA logs show repeated short-to-medium downtime events tagged to the label applicator station, often with label sensor or photocell fault codes and a rising missing-label or label-reject counter. The applicator or labeling axis state alternates between running and fault/stopped, while upstream filling or capping may continue briefly causing blocking until the line is halted.

Countermeasure

Engineering guidance

Control label stock quality and storage conditions to keep adhesive tack and die-cut dimensions within specification, and verify incoming reels against applicator tolerances before loading. Maintain and periodically clean the peel plate, rollers and sensors, and adjust tension, dispensing speed and sensor sensitivity to the specific label format in use.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Number of events: 1,595 occurrences · as reported: “sticky labels, jammed labels, labels too short or too long, and labels getting caught”
    Show verbatim quote
    These problems have caused downtime from October to December 2023, with a total downtime of 6448 minutes and a frequency of 1595 occurrences.
  2. Lost time: 6,448 minutes · as reported: “sticky labels, jammed labels, labels too short or too long, and labels getting caught”
    Show verbatim quote
    These problems have caused downtime from October to December 2023, with a total downtime of 6448 minutes and a frequency of 1595 occurrences.