foratvise
Get Started
Idling and minor stops (micro-stops)

Component fouling from residue and degraded lubricant

Idling and minor stops (micro-stops)PerformanceWhole line or unspecified equipment

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 53 % of the line's lost time. Reported by 1 of the 127 studies that could observe it (sparse evidence).

What happens

Over time, product residue, dust or debris accumulates on moving parts, or lubricant oxidizes and loses viscosity (burning) under heat and friction, so that the lubricating film breaks down. This allows direct metal-to-metal contact or sticky deposits to restrict the free movement of rollers, guides, chains or shafts, causing the component to seize or jam intermittently.

What is done about it

Implement a scheduled lubrication and cleaning program sized to actual soiling and thermal load, using the correct lubricant grade for the operating temperature, and inspect/replace lubricant before it degrades. Add routine wipe-down or residue removal on exposed moving parts and monitor component temperature or current as an early warning of friction build-up.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.5% [0.1–1.4%]
Expected share of lost time
0.3% [0.1–0.7%]
Share of lost time when present
53% [41–65%]
Studies / units
127 / 161
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.1–2.2%]13 studies
  • Soft drinks, bottled water and juices
    0.5% [0.1–1.8%]26 studies
  • Brewing, wine and spirits
    0.6% [0.1–2.1%]11 studies
  • Bakery and pasta
    0.5% [0.1–1.9%]24 studies
  • Meat, poultry and seafood
    0.6% [0.1–2.2%]9 studies
  • Fruit and vegetable processing
    0.6% [0.1–2.1%]7 studies
  • Grain and oilseed milling
    0.9% [0.1–3.5%]6 studies
  • Sugar and confectionery
    0.6% [0.1–2.2%]9 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.1–2.2%]5 studies
  • Animal feed and pet food
    0.6% [0.1–2.4%]7 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.1–2.2%]10 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Over time, product residue, dust or debris accumulates on moving parts, or lubricant oxidizes and loses viscosity (burning) under heat and friction, so that the lubricating film breaks down. This allows direct metal-to-metal contact or sticky deposits to restrict the free movement of rollers, guides, chains or shafts, causing the component to seize or jam intermittently.

How it looks in SCADA data

Engineering guidance

Short, recurring stop events on the same component or axis, often with rising motor current or torque trend prior to the stop, and no fault code requiring maintenance intervention beyond operator clearing. Historical trend shows increasing frequency of micro-stops as lubricant condition or fouling worsens between cleaning/lubrication cycles.

Countermeasure

Engineering guidance

Implement a scheduled lubrication and cleaning program sized to actual soiling and thermal load, using the correct lubricant grade for the operating temperature, and inspect/replace lubricant before it degrades. Add routine wipe-down or residue removal on exposed moving parts and monitor component temperature or current as an early warning of friction build-up.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of planned time: 3.45 % · as reported: “friction between components caused by burnt lubricant”
    Show verbatim quote
    High downtime rate due to friction between components caused by burnt lubricant 3.45% 2.17% 2.90%
  2. Share of planned time: 10.4 % · as reported: “component blockage caused by residue buildup”
    Show verbatim quote
    High downtime rate due to component blockage caused by residue buildup 10.39% 6.52% 3.48%