foratvise
Get Started
Equipment failure (breakdowns)

Automatic lubricator (oiler) failure

Equipment failure (breakdowns)AvailabilityWhole line or unspecified equipment

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 0 of the 127 studies that could observe it (sparse evidence).

What happens

The automatic oiler that supplies lubricant to chains, bearings or guides fails because of a jammed pump, clogged delivery line, empty reservoir or faulty drive/sensor, interrupting the lubricant feed. The line control system then stops the equipment to prevent dry-running damage to the lubricated components.

What is done about it

Implement a preventive maintenance routine that checks reservoir level, cleans filters and delivery lines, and tests pump/motor operation and level or flow sensors on a fixed schedule. Add predictive monitoring of lubricant flow or pressure so refills and component replacement happen before the oiler actually stops delivering.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.4% [0.1–1.1%]
Expected share of lost time
0.2% [0.0–0.6%]
Share of lost time when present
57% [46–67%]
Studies / units
127 / 161
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.4% [0.0–1.7%]13 studies
  • Soft drinks, bottled water and juices
    0.4% [0.0–1.3%]26 studies
  • Brewing, wine and spirits
    0.4% [0.0–1.6%]11 studies
  • Bakery and pasta
    0.4% [0.0–1.5%]24 studies
  • Meat, poultry and seafood
    0.4% [0.0–1.6%]9 studies
  • Fruit and vegetable processing
    0.5% [0.0–1.8%]7 studies
  • Grain and oilseed milling
    0.4% [0.0–1.7%]6 studies
  • Sugar and confectionery
    0.4% [0.0–1.6%]9 studies
  • Snacks, coffee, tea and other foods
    0.4% [0.0–1.7%]5 studies
  • Animal feed and pet food
    0.4% [0.0–1.8%]7 studies
  • Food manufacturing (unspecified or mixed)
    0.4% [0.0–1.7%]10 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The automatic oiler that supplies lubricant to chains, bearings or guides fails because of a jammed pump, clogged delivery line, empty reservoir or faulty drive/sensor, interrupting the lubricant feed. The line control system then stops the equipment to prevent dry-running damage to the lubricated components.

How it looks in SCADA data

Engineering guidance

A dedicated lubrication fault alarm or low-level/low-pressure flag is raised, the oiler motor or pump run-status signal drops to zero while the main line is commanded to run, and the line transitions into a fault/stopped state with the oiler listed as the triggering device. Downstream and upstream equipment show starvation or blocking states correlated with the oiler fault timestamp.

Countermeasure

Engineering guidance

Implement a preventive maintenance routine that checks reservoir level, cleans filters and delivery lines, and tests pump/motor operation and level or flow sensors on a fixed schedule. Add predictive monitoring of lubricant flow or pressure so refills and component replacement happen before the oiler actually stops delivering.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 12.0 min · as reported: “Oiler Stopping”
    Show verbatim quote
    Oiler Stopping 7 5 12