foratvise
Get Started
Setup and adjustments

Manual bottle pushing in pasteurizer

Setup and adjustmentsAvailabilityPasteurization

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 56 % of the line's lost time. Reported by 0 of the 26 studies that could observe it (sparse evidence).

What happens

During warm-up or changeover of the pasteurizer, the conveying chain inside the tunnel does not yet run at a stable synchronized pace, so bottles can stall, tip or bunch up as they pass through the spray zones. Operators intervene manually, pushing the containers along the chain to keep the batch moving until thermal and mechanical conditions stabilize.

What is done about it

Improve conveyor chain synchronization and lubrication, and program a controlled warm-up ramp with gradual speed increase so the chain reaches stable pace before full-speed operation, reducing the need for manual pushing. Standardize the changeover and start-up procedure to minimize the duration of this unstable transition period.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.5% [0.1–1.9%]
Expected share of lost time
0.3% [0.0–1.0%]
Share of lost time when present
56% [44–66%]
Studies / units
26 / 29
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.0–2.7%]6 studies
  • Soft drinks, bottled water and juices
    0.6% [0.1–2.9%]1 study
  • Brewing, wine and spirits
    0.6% [0.0–2.8%]0 studies
  • Bakery and pasta
    0.7% [0.0–3.0%]0 studies
  • Meat, poultry and seafood
    0.6% [0.0–2.8%]0 studies
  • Fruit and vegetable processing
    0.6% [0.0–2.5%]2 studies
  • Grain and oilseed milling
    0.6% [0.1–2.7%]0 studies
  • Sugar and confectionery
    0.6% [0.0–2.7%]3 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.0–2.8%]3 studies
  • Animal feed and pet food
    0.6% [0.0–2.7%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.0–2.6%]7 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

During warm-up or changeover of the pasteurizer, the conveying chain inside the tunnel does not yet run at a stable synchronized pace, so bottles can stall, tip or bunch up as they pass through the spray zones. Operators intervene manually, pushing the containers along the chain to keep the batch moving until thermal and mechanical conditions stabilize.

How it looks in SCADA data

Engineering guidance

The pasteurizer conveyor speed or chain drive signal shows irregular or intermittent movement during the setup/warm-up window, often without any fault alarm being raised, while upstream filling and downstream labeling show starvation or blocking patterns tied to the pasteurizer state. Operator presence or manual-mode flags may coincide with these intervals if logged.

Countermeasure

Engineering guidance

Improve conveyor chain synchronization and lubrication, and program a controlled warm-up ramp with gradual speed increase so the chain reaches stable pace before full-speed operation, reducing the need for manual pushing. Standardize the changeover and start-up procedure to minimize the duration of this unstable transition period.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 6.00 min · as reported: “Empurrar garrafas no pasteurizador”
    Show verbatim quote
    10 Empurrar garrafas no pasteurizador 6 0
  2. Lost time: 0 min · as reported: “Empurrar garrafas no pasteurizador”
    Show verbatim quote
    10 Empurrar garrafas no pasteurizador 6 0