foratvise
Get Started
Process defects (scrap and rework)

Manual filling/weighing variation

Process defects (scrap and rework)QualityFilling

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 48 % of the line's lost time. Reported by 0 of the 120 studies that could observe it (sparse evidence).

What happens

When filling or weighing is performed manually by operators rather than by automated dosing, pack weights drift above or below target because of inconsistent operator technique, fatigue, scoop or pour variability, and lack of real-time feedback correction. This produces a wide, operator-dependent weight distribution that generates both underweight packs (compliance risk) and overweight packs (giveaway) within the same run.

What is done about it

Replace or assist the manual step with automated dosing, filling or weighing equipment with closed-loop weight feedback, and where manual operation must remain, standardize the work method, provide calibrated aids and reference weights, and train and periodically audit operators. In-line checkweighing with automatic feedback to the filling step and statistical process control monitoring help detect and correct drift before it generates nonconforming packs.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.4% [0.1–1.1%]
Expected share of lost time
0.2% [0.0–0.5%]
Share of lost time when present
48% [36–60%]
Studies / units
120 / 162
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.4% [0.0–1.6%]18 studies
  • Soft drinks, bottled water and juices
    0.4% [0.0–1.3%]44 studies
  • Brewing, wine and spirits
    0.4% [0.0–1.6%]16 studies
  • Bakery and pasta
    0.5% [0.0–1.9%]0 studies
  • Meat, poultry and seafood
    0.4% [0.0–1.7%]6 studies
  • Fruit and vegetable processing
    0.4% [0.0–1.8%]4 studies
  • Grain and oilseed milling
    0.5% [0.0–1.8%]6 studies
  • Sugar and confectionery
    0.4% [0.0–1.7%]3 studies
  • Snacks, coffee, tea and other foods
    0.4% [0.0–1.7%]6 studies
  • Animal feed and pet food
    0.4% [0.0–1.7%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.4% [0.0–1.6%]13 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

When filling or weighing is performed manually by operators rather than by automated dosing, pack weights drift above or below target because of inconsistent operator technique, fatigue, scoop or pour variability, and lack of real-time feedback correction. This produces a wide, operator-dependent weight distribution that generates both underweight packs (compliance risk) and overweight packs (giveaway) within the same run.

How it looks in SCADA data

Engineering guidance

Checkweigher or in-line scale data shows a wide, operator- or shift-dependent weight distribution with frequent high/low flags that do not correlate with any equipment fault or downtime state. Reject counters for over/under weight rise without associated machine stops, and statistical process control charts show poor process capability rather than drift tied to a specific component.

Countermeasure

Engineering guidance

Replace or assist the manual step with automated dosing, filling or weighing equipment with closed-loop weight feedback, and where manual operation must remain, standardize the work method, provide calibrated aids and reference weights, and train and periodically audit operators. In-line checkweighing with automatic feedback to the filling step and statistical process control monitoring help detect and correct drift before it generates nonconforming packs.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 0 ton · as reported: “Defects - labor manual process over/under weight packs”
    Show verbatim quote
    Average waste Per Month (Ton/Month) 0